Abs; Ply Wood; 3, Laser-Cut; Steel - Krick Ro Marin Happy Hunter Notice De Montage Et De Mise En Œuvre

Crane swivel mechanism
Part Description
No.
107 Base plate
108 Side panel
109 Motor support
110 Motor, geared 500 : 1
111 End-support
112 Shaft
113 Worm gear
114 Grubscrew with cutter tip
115 Washer
116 Coupling sleeve
117 Block
118 Self-tapping screw
29 K Tubular rivet
- Refer to photos 86 - 88 and the detail drawing of the
swivel mechanism.
- Glue the side panel 108 and the motor support 109 to
the base plate 107. Install the geared motor 110.
- Assemble parts 112 - 115 and connect the shaft to the
motor using the coupling sleeve. Check that the parts
line up correctly and rotate freely, then glue the end-
support in place.
- Fit the obechi block 117 flush with the top edge of the
side panel.
The towing mechanism
Part Description
No.
119 Base plate
120 Former
121 Brace
122 Tube
123 Servo mount
124 Servo
125 Pushrod
126 Profiled rail
127 R.H. support
128 L.H. support
129 Switch
130 Self-tapping screw
- Refer to the drawing of the towing mechanism on Plan
I and photos 89 - 95.
- Glue parts 119 - 121 together. Glue the tube 122 to
the former 120, and cut a 5 mm slot in it as shown.
- Glue each 2 of the servo mount parts together, pre
drill the holes for servo screws. Place the servo mount
123 in position, and fit the servo 124 in the mount.
- Cut down a cruciform servo output device and connect
the pushrod 125 to it. Slip the pushrod in the sleeve
122 and attach the output arm to the servo. - Check
that the system works properly: at one end-point the
pushrod must clear the gap between the tubes; at the
other end-point it must close it reliably.
- Glue the profiled rails 126 to the inside of the supports
127 and 128, leaving a gap 3.5 mm wide. Ensure that
the rails are parallel to each other.
Material

ABS

ABS
ABS
---
ABS
Brass
Brass

Steel

Brass
Plastic

Ply wood

Steel
Brass
Material
Ply wood
Ply wood
Ply wood
Brass
Ply wood
---
Steel
ABS
ABS
ABS
---
Steel
© Klaus Krick Modelltechnik, Germany, Stand 06.2017
Size in mm
1.5, laser-cut
1.5, laser-cut
1.5, laser-cut
---
1.5, laser-cut
2 Ø x 41
10 Ø
M3 x 3
2.2 I.D.
1.0 I.D. x 20
5, laser-cut
2.2 Ø x 9.5
3 Ø x 4
- Place the completed mechanism on the underside of
the deck and align it with the spur gear 105. Adjust the
position of the spur gear if necessary until it is central
relative to the worm gear. Glue the block 117 to the
edge of the hatch only.
- The mechanism is wired up at a later stage.
- Fit the tubular rivet 29 K in the underside of the tube
11 K, and secure it with a drop of cyano. File the rivet
flange back flush with the end of the tube.
Size in mm

3, laser-cut

3, laser-cut
3, laser-cut
2.2 Ø x 3 Ø x 40
3, laser-cut
---
1.5 Ø x 180
3.5 x 9 x 101
1.5, laser-cut
1.5, laser-cut
---
2.2 Ø x 9.5
- Offer up the completed rails to the towing mechanism.
- Drill the 2.3 mm Ø holes for the screws, and fit the
screws temporarily.
- Glue the assemblies 126, 127 (right) and 126, 128
(left) in the hull. Fit the towing mechanism and check
that it is correctly positioned.
No. Notes
off
1 plate 5
1 plate 3
1 plate 4
1 Not included
2
1
1 FS
2 FS
2
1
1 plate 8
2
1
No. Notes
off
1 plate 9
1 plate 9
1 plate 9
1
4 plate 9
1 Not included
1 One Z-bend
4 plate 3
1 plate 3
1
1 Not included
2
9