Krick Ro Marin Happy Hunter Notice De Montage Et De Mise En Œuvre page 40

Figs. 140 - 144 show the sprues containing the injection-moulded parts required for the following stages.
Hatches and toolbox, Figs. 145 - 147, Plan I
Part Description
No.
253 Hatch frame 43 x 43 x 15
254 Tension frame
255 Spacer plate
256 Cover
257 Hatch cover
258 Handwheel
259 Hatch round
260 Hatch cover
261 Handwheel
262 Hatch box 16 x 16 x 12
263 Hatch floor
264 Hatch cover
265 Handwheel
266 Box 16 x 22 x 12
267 Cover
268 Hatch block 18 x 18 x 12
269 Sliding hatch
270 Handle
271 Latch bolt
272 Hatch block 22 x 22 x 10
273 Tension frame
274 Spacer plate
275 Hatch cover
276 Davit brace
277 Davit
278 Handle
The hatches consist of ABS laser cut sides or short
pieces of tube, fitted with additional laser-cut ABS com-
ponents; the parts should be glued together using cyano.
Make up the individual hatches according to the detail
drawings on the plan.
- Glue together the oil tank entry hatch from parts 254 -
258, and place it on the hatch 62.
- Assemble the rudder compartment escape hatch from
parts 259 to 261, and glue it on the after deck in the
position shown in the plan view.
- Use parts 262 - 265 to make the after bulkhead es-
cape hatch, and glue the hatch in place as shown on
the plan.
- Glue the cover 267 on the toolbox 266. The box
cannot be installed until the superstructure has been
completed.
- Make up the freshwater tank hatch from parts 268 -
16
Material
ObABSechi
ABS
ABS
ABS
Resin
Plastic
ABS
Resin
Plastic
ABS
ABS
Resin
Plastic
ABS
ABS
ABS
ABS
Brass
Brass
ABS
ABS
ABS
ABS
ABS
ABS
Brass
© Klaus Krick Modelltechnik, Germany, Stand 06.2017
Size in mm
1.5, laser-cut
1, laser-cut
1.5, laser-cut
1, laser-cut
15 Ø cast
7 Ø
14 Ø x 11
15 Ø cast
7 Ø
1.5, laser-cut
1, laser-cut
15 Ø cast
7 Ø
1.5, laser-cut
1, laser-cut
1.5, laser-cut
1, laser-cut
0.7 Ø
0.7 Ø
1.5, laser-cut
1, laser-cut
1.5, laser-cut
1, laser-cut
1, laser-cut
Inj. moulded
0.7 Ø
271. Drill the 1 mm Ø holes for the handles 270 and
the latch bolt 271. Bend parts 270 and 271 to shape
from pieces of brass tube, and glue them in the holes.
- The forecastle deck hatch is assembled from parts
272 - 278. Before gluing the tension frame 273 in
place, drill the 3 mm Ø hole for the davit 277. Brace
the davit with the davit support 276. Drill 1 mm Ø
holes in the spacer plate 274 for the two handles 278.
- Glue the completed hatch to the forecastle deck.
No. Notes
off
4 plate 6
1 plate 7
1 plate 2
1 plate 7
1
1 FS
1
1
1 FS
4 plate 6
1 plate 7
1
1 FS
4 plate 6
1 plate 7
4 plate 6
1 plate 7
2 As plan
2 As plan
4 plate 6
1 plate 7
1 plate 2
1 plate 7
1 plate 7
1
2 As plan