Use Only As Authorized - Scheppach 19013 04901 Traduction Des Instructions D'origine

• If a second Person is at the circular saw bench to remove
cut workpieces, the machine must be equipped with a
table extension. The second per- son may only stand at the
removal end of the table extension.
• Fit only sharp, crack-free and undistorted circular saw
blades.
• Circular saw blades made of super-high-speed steel must
not be used.
• Safety devices on the machine must not be dismantled or
put out of action.
• The splitting wedge is an important safety feature. The
workpiece is fed through the splitting wedge, which
prevents the cut from closing behind the saw blade and
also prevents the workpiece from kicking back.
• Always lower the protective Cover over the work- piece for
each operation.
• The cowl must stand horizontally above the saw blade
during all working procedures
• Always use the push-stick for longitudinal cutting of narrow
workpieces of less than 120 mm.
• Always stop the machine and disconnect the mains plug
before remedying faults or removing jammed pieces of
wood.
• Replace the blade-slot insert if it is damaged. Disconnect
the mains plug!
• Wear only close-fitting clothes. Remove rings, bracelets
and other jewelry.
• Pay attention to the rotational direction of the motor and
tool - See Electrical Connection.
• Cleaning, changing, calibrating, and setting of the machine
may only be carried out when the motor is switched off.
Pull the power supply plug and wait for the rotating tool to
completely stop.
• Switch the machine off and pull power supply plug when
rectifying any malfunctions
• For all working procedures the machine must be connected
to a scheppach Dust extractor. Observe instructions for proper
use.
• When working on the machine, all safety mecha- nisms and
Covers must be mounted.
• Circular saw blades made from superspeed steel may not
be used.
• The splitting wedge is an important safety feature. The
workpiece is fed through the splitting wedge, which
prevents the cut from closing behind the saw blade and
also prevents the workpiece from kicking back.
• Note the thickness of the splitting wedge - See figures
stamped into the splitting wedge. The splitting wedge may
not be thinner than the saw blade and not thicker than
cutting joint width.
• Before the machine is put into operation it must be
connected to a dust extractor with a flexible, non-flammable
suction hose. The suction should switch on automatically
when the machine is switched on.
• When leaving the work place, switch the motor off. Pull the
power supply plug.
• Cut off the external power supply of the machine or plant
even if only minor changes of place are envisaged. Properly
reconnect the machine to the supply mains before
recommissioning.
• Connection and repair work on the electrical installation
may be carried out by a qualified electrician only.
• All protection and safety devices must be replaced after
completing repair and maintenance procedures.
• Pay attention to an sufficient illumination of the
workplace.
• Proof the braking time till the saw blade stopps daily.
It must not be longer than 10 seconds, otherwise do not
continue working.
• Always wear ear protection and protection glasses during
working
• Wear gloves when you change the saw blade
• Power down the machine when you clean it
• Operating conditions: Do not use the machine outside only
inside in closed rooms
• Store conditions: humidity should not be under 90% and
not condensed
• Safe big work pieces of canting

Use only as authorized

• The machine corresponds to the valid EC guideline.
• The scheppach Precisa 6.0 circular sawbench is defined as a
machine in accor- dance with EN 1870-1.
• For transporting the machine within the workshop area use
the scheppach wheel assembly (accessory)
• The working position is to the front of the machine either
to the right or the left sawblade.
• The machining range and surrounding areas of the machine
must be clear of interfering foreign mat- ter to prevent
accidents occurring.
• Workpieces must be completely free of foreign objects, i.e.
nails or screws.
• Before the machine is put into operation it must be
connected to a dust extractor with a flexible, non-flammable
suction hose. The suction should switch on automatically
when the machine is switched On.
• Use the scheppach dust extractor ha 3200 or ha 2600 to
remove matchwood or saw dust. The vacuum support flow
rate must be 20 mls. Subat- mospheric pressure
1200 Pa.
• The scheppach automatic switching unit is avai- lable as a
special accessory.
Typ ALV 2
Art. Nr. 791 0 401 0 230 V150 Hz
Typ ALV 10
Art. Nr. 791 0 4020 400 V150 Hz
The vacuum exhaust unit automatically switches on after a
2-3 second delay after the machine tool is turned On. This
avoids overloading the circuit fuse.
After turning off the machine tool, the vacuum exhaust unit
remains on for an additional 3 - 4 seconds and is then
automatically switched off. Remaining dust is thereby
removed by vacuum exhaust, as required by German
regulations governing hazardous materials. This results in
savings in electricity consumption and reduces noise
levels, as the vacuum exhaust unit is on only during
machine tool operation.
For work in commercial spaces, the scheppach dust
extractor rg 4000 must be used. Do not remove or shut off
vacuum exhaust systems or dust removers while machine
tools are operating.
• The scheppach circular sawbench is designed exclusively
for the machining of wood and materi- als similar to wood.
Only original scheppach tools and accessories may be
used. Use the required sawblade in accordance with the
EN 847-1 norm depending on the type of cut and type of
wood (solid wood, plywood or chipboard). Please observe
the scheppach ,,Special Tool Accessories" (page 18).
english 17