Use Only As Authorized - Scheppach basato 3 Mode D'emploi

• When working on the machine, all safety mechanisms
and covers must be mounted.
• Keep children away from the machine when it is con-
nected to the power supply.
• Operating personal must be at least 18 years of age.
Trainees must be at least 16 years of age, but may only
operate the machine under adult supervision.
• Persons working on the machine may be not diverted
from their work.
• The working space on the machine must be free of
chips and wood scrap.
• Wear only close-fitting clothes. Remove rings, bracelets
and other jewelry.
• Always wear safety goggles when working.
• Wear a cap or hair net to protect long hair.
• Wear suitable gloves to change the sawband.
• Do not wear work gloves when working on the saw.
• Observe the correct rotational speed setting on the ma-
chine.
• The safety mechanism on the machine may not be re-
moved or rendered unusable.
• Cleaning, changing, calibrating, and setting of the ma-
chine may only be carried out when the motor is
switched off. Pull the power supply plug and wait for
the rotating tool to completely stop.
• Connection and repair work on the electrical installation
may be carried out by a qualified electrican only.
• All protection and safety devices must be replaced after
completing repair and maintenance procedures.
• Switch the machine off and pull power supply plug
when rectifying any malfunctions.
• Use a suction unit to suck up wood shavings and saw-
dust. The current speed at the suction connection piece
should be 20 m/s.
• Check the saw band guide and the saw band tension
before starting up.
• Do not use nicked saw bands or those that have an al-
tered form.
• Replace table inserts that have worn saw slots.
• When sawing round wood, make sure that the work
piece does not turn.
• For sawing heavy or cumbersome pieces, use the appro-
priate working
(Special accessory roller stands).
• Place the upper saw band guide as closely as possible
to the work piece.
• On slanted table plates, attach the longitudinal stop on
the lower table plate half.
• Do not brake the saw band with side pressure after
switching off.
• Remove work pieces that have become stuck only with
the motor switched off and with the saw band at a
standstill.
• Cut off the external power supply of the machine even if
only minor changes of place are envisaged. Properly re-
connect the machine to the supply mains before recom-
missioning.
• When leaving the work place, switch the motor off. Pull
the power supply plug.
GB8
aids for bracing.

Use only as authorized

CE tested machines meet all valid EC
machine guidelines as well as all
relevant guidelines for each machine.
• All protective and safety device must be mounted on
the machine before beginning work.
• The machine is designed to be operated by one person.
The operator is responsible for all other persons in the
working area.
• Observe all safety instructions and warnings attached to
the machine.
• See to it that safety instructions and warnings attached
to the machine are always complete and perfectly legi-
ble.
• The bandsaw with the supplied tools and accessories is
designed exclusively for sawing wood, material similar
to wood, and non-ferrous metals and steel.
• The maximum dimensions for workpieces to be
processed is may not exceed the bench size in the stan-
dard version. Clearance width: 306 mm, Clearance
height: 160 mm
• For larger workpiece dimensions which require tipping
of the table top, the table extension or the dolly (special
accessories) must be used.
• The band saw can also be used for sawing metal when it
is equipped with a special saw band dolly (special ac-
cessory) and a operated at an adapted cutting speed.
Metal allows with more than 80 % magnesium may not
be processed due to the danger of fires.
• When used in enclosed rooms, the machine must be
connected to a vacuum exhaust unit. Use the dust ex-
tractor to remove matchwood or saw dust. The vacuum
support flow rate must be 20 m/s. Subatmospheric
pressure 860 Pa.
• The automatic switching unit is available as a special
accessory.
Type ALV 2 Art. No. 7910 4010 230 V/50 Hz
Type ALV 10 Art. No. 7910 4020 400 V/230 V/50 Hz
• The vacuum exhaust unit automatically switches on af-
ter a 2-3 second delay after the machine tool is turned
on. This avoids overloading the circuit fuse.
• After turning off the machine tool, the vacuum exhaust
unit remains on for an additional 2-3 seconds and is
then automatically switched off. Remaining dust is
thereby removed by vacuum exhaust, as required by
German regulations governing hazardous materials. This
results in savings in electricity consumption and re-
duces noise levels, as the vacuum exhaust unit is on
only during machine tool operation.
• A suction device which conforms with commercial regu-
lations must be used for suction in commercial areas.
• Do not switch off or remove suction units or dust extrac-
tors while the work machine is in operation.
• The machine must only be used in technically perfect
condition in accordance with its designated use and the
instructions set out in the operating manual, and only
by safety-conscious persons who are fully aware of the
risks involved in operating the machine. Any functional
disorders, especially those affecting the safety of the
machine, should therefore be rectified immediately.
• The safety, work and maintenance instructions of the
manufacturer as well as the technical data given in the
calibrations and dimensions must be adhered to.
• Relevant accident prevention regulations and other,
generally recognized safety-technical rules must also be
adhered to.
• The machine may only be used, maintained, and oper-