Technical Data - Scheppach 19013 04901 Traduction Des Instructions D'origine

sawblade
Special low noise sawblade, hardened metal tipped for
plastic coated furniture boards.
Dimensions:
Total Ø mm 300
Bohrung Ø mm 30
No. of teeth 60 Z
sawblade
Universal trimming blade for soft and hard wood.
Dimensions:
Total Ø mm 300
Bore Ø mm 30
No. of teeth 28 WZ
Scoring sawblade
Hardened metal sawblade for scoring plastic coated
furniture boards.
Dimensions:
Total Ø mm 120
Bore Ø mm 20
No. of teeth 26 Z

Technical data

Dimensions:
general length
total length with table extension
total width
total height
table size
table height
circular sawblade Ø max.
circular sawblade Ø min.
cut height 90°
cut height 45°
sawblade adiustment ranae
rotary speed
cutting speed
scoring sawblade Ø
scoring sawblade rotary speed
cutting speed - scoring
parallel stop longitudina
parallel cut max. width
parallel cut width with table width
extension - foldable
angling fence
angling fence guide
7986 3001 Cut width 90" angular cut:
with Cross / mitre gauge
with sliding table carriage 1400
with sliding table carriage 2000
suction connection piece Ø
suction connection piece Ø
suction volume flow at 20 m/s
suction at suction connection piece
5100 5501
ambient conditions
nett weight
nett weight with scorer
Drive
5472 0313 Electric motor
input power P1
output power P2
motor rotary speed 1/min.
drive type
rated current
Scorer
input power P1
output power P2
Measurement conditions in accordance with draft pr EN 1870-
1: 1995-07; DIN EN ISO 11202; DIN EN ISO 3746
The values stated are emission values and are there- fore
not necessarily safe operating values. Although there is a
correlation between emission and immis- sion levels, you
cannot reliably deduce from this whether additional safety
measures are required or not. Factors which can influence
the immission level currently at the workstation comprise
mm 1100 the duration of the effects, the characteristics of the work
mm 1400 room, other sources of noise etc., for example, the
mm 760 number of machines and adjacent operations. The
mm 1110 permissible values per workstation can also vary from
mm 805x680 country to country. This information should nevertheless
mm 850 enable the user to make a better esti- mation of dangers
mm 315 and risks.
mm 250
mm 110 Sound intensity level in dB
mm 77 ldling L
mm 110 Working L
1/min. 4000 Work place based emission values in dB
m/sec. 66 ldling L
mm 120 Working L
1/min. 8000
m/sec. 50 A measurement error factor of K = 4 dB applies to the
mm 800 stated emission values.
mm 390
mm 1100 lnformation on dust emission
0-60° The dust emission values measured in accordance with
mm T-Profil the „principles for testing dust emission" of the
committee of experts of wood are below 2 mg/m3. This
means that the TRK limit for wood dust which is valid in
the Federal Republic of Germany will be per- manently
kept to if the machine is connected to a properly working
dust extractor with at least 20 mls air speed.
230V
50 Hz
kW 3,0
kW 2,2
2800
S6/40%
11,6 A
kW 0,8
kW 0,5
Noise characteristic values
=
WA
=
WA
=
pAeq
=
pAeq
mm 270
mm 900
mm 960
mm 50
mm 100
Ø 100 = 560 m³/h
Ø 100 = 170 Pa
Ø 50 = 918 Pa
- 5° C
+ 35° C
kg 215
kg 224
400V
50 Hz
4,8
4,0
2800
S6/40%
8,2 A
97,5 dB(A),
100,4 dB(A)
86,7 dB(A),
87,1 dB(A)
english 19