Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Do not operate machine before having read the
operating instructions, understood all the notes and
assembly the machine as described here.
Keep the instructions in a safe place for future use.
Contents
Declaration of conformity
Extent of delivery
Characteristics noise values
Operating times
Symbols: operating manual
Safety working
EC Declaration of Conformity
No. (S-No.): 27778
according to EC directive 2006/42/EC
We,
Altrad Lescha Atika GmbH
Josef-Drexler-Str. 8, 89331 Burgau - Germany
herewith declare under our sole responsibility that the product
Brennholzwippkreissäge (Log saw) BWS 400-2
Serial number: 000001 - 020000
is conform with the above mentioned EC directives as well as with the
provisions of the guidelines below:
2014/30/EU and 2011/65/EU.
Following harmonized standards have been applied:
EN 1870-6:2017; EN 60204-1:2006+A1; EN 55014-1:2006+A1+A2;
EN 55014-2:1997+A1+A2; EN 61000-3-2:2014; EN 61000-3-3:2013
Duly authorised person for the complilation of technical documents:
Altrad Lescha Atika GmbH - Technical department
Josef-Drexler-Str. 8 - 89331 Burgau - Germany
i.A.
Burgau, 31.07.2020
Engineering design management
11
11
11
11
11
12
12
12
12
14
14
15
15
16
16
17
17
17
17
17
17
18
18
i.A. G. Koppenstein
Extent of delivery
Frame
1
2
Saw blade casing inside
Saw blade cover inside
3
4
Saw blade casing outside
5
Saw blade cover outside
6
Limit plate
7
Handle
8
Holding plate
9
Adjusting plate
10
Jigging device
11
Safety flap
12
Rear wall right
After unpacking, check the contents of the box
That it is complete
►
Check for possible transport damage
►
Report any damage or missing items to your dealer, supplier or the
manufacturer immediately. Complaints made at a later date will not be
acknowledged.
Packaging material can be recycled and should be brought to an eco-
friendly recycling facility.
Characteristics noise values
DIN EN ISO 3746 :2010
Use of the machine as log saw for firewood with standard saw blade.
Noise power level Sound pressure level at the workplace
Load
L
= 115 dB(A)
WA
The factor of measurement uncertainty is 4 dB.
The values given are emission values and must therefore not simultaneously
represent safe workplace values too. Although there is a relationship between
emission and immersion levels, it can be reliably deduced whether additional
precautionary measures are necessary or not. Factors, which can influence the
immersion level currently existing at the workplace include the duration of the
effects, the special type of the workroom, other noise sources, etc. e.g. the
number of machines and other adjacent processes. The permissible workplace
values can also vary from country to country. This information should however
enable an improved assessment of the danger and risk to be carried out.
Operating times
Before initiating the device please observe the provisions pertaining to
corresponding laws (regional provisions) for the noise control.
Symbols operating instructions
Threatened hazard or hazardous situation. Not observing
this instruction can lead to injuries or cause damage to
property.
Important information on proper handling. Not observing
this instruction can lead to faults.
User information. This information helps you to use all the
functions optimally.
Assembly, operation and servicing. Here you are explained
exactly what to do.
Please refer to the attached assembly and
operating instruction sheet for references to figure
numbers in the text.
...
13
Front saw blade flange
14
Saw blade ( 405 mm)
15
Rear saw blade flange
16
Rear wall left
17
Support extension
18
Brace 2x
19
Support pin cpl.
20
Mounting accessories
21
Mounting tools
22
Operating manual
23
Assembly and operating
instruction sheet
Warranty declaration
L
= 96 dB(A)
PA
11
Publicité
Chapitres
Table des Matières
