Installation Instructions; Intended Use; Approval; Tools And Facilities Required - Truma Mover XT Instructions De Montage

– Installation of replacement, supplementary or accessory
parts that are not original manufacturer's parts or which
have not been approved by the manufacturer. If the device
is subject to networked control, this applies, in particular,
if the control units or the software have not been approved
by Truma or if the Truma control unit (e.g. Truma CP plus or
Truma iNet Box) has not been exclusively used for control-
ling Truma devices or devices approved by Truma.
– Damage arising from foreign substances (e.g. oil or, plas-
ticisers in the gas), chemical or electrochemical influences
in the water, or cases when the unit has come into con-
tact with unsuitable substances (e.g. chemical products,
flammable substances or unsuitable cleaning agents)
– Damage caused by abnormal environmental or unsuitable
operating conditions
– Damage caused by force majeure or natural disasters or
any other influences not within Truma's responsibility
– Damage resulting from improper transport
– End customer's or third-party modifications of the device,
including any replacement, supplementary or accessory
parts, or installation of the same, especially concerning the
exhaust gas system or the cowl.
3. Making a warranty claim
The warranty must be claimed with an authorised service part-
ner or at the Truma Service Centre. All the relevant addresses
and phone numbers can be found at www.truma.com, in the
"Service" section.
The Manufacturer's address is:
Truma Gerätetechnik GmbH & Co. KG
Truma Servicezentrum
Wernher-von- Braun-Straße 12
85640 Putzbrunn, Germany
To ensure a smooth procedure, we should be grateful if you
could have the following details ready before contacting us:
– Detailed description of the defect
– Serial number of the unit
– Date of purchase
The authorised service partner or the Truma Service Centre will
then specify the further procedure. To avoid transport damage,
the affected unit must only be shipped upon prior arrangement
with the authorised service partner or the Truma Service Centre.
If the warranty claim is recognised by the Manufacturer, then
the transport expenses shall be borne by the same. If no war-
ranty claim is applicable, the Consumer will be notified ac-
cordingly and any repair and transport expenses shall then be
the Consumer's liability. We must ask you not to send in a unit
without prior arrangement.

Installation instructions

Only competent and trained persons (experts) may in-
stall, repair and carry out the functional test on the Tru-
ma product in accordance with the installation and operating
instructions and the currently accepted technical regulations.
Experts are persons who, based on their specialist instruc-
tion and training, their knowledge and experience with Truma
products and the relevant standards, can carry out the neces-
sary work properly and identify potential hazards.
Please ensure that no metal chips or other contaminants get
into the control unit during installation.
In the case of screws with sealant, make sure that the
thread is free of grease / oil.

Intended use

The Mover XT was designed for use on single-axle
caravans with a gross weight of up to 2300 kg.
The Mover XT2 was designed for use on dual-axle
caravans with a gross weight of up to 2400 kg.
The Mover XT / XT2 weighs approx. 28 kg.
Check the maximum towable weight for your towing
vehicle and the gross weight of your caravan to make
sure that they are designed for this additional weight.

Approval

The Truma Mover XT / XT2 has design approval, and a "gen-
eral operating permit" (ABE) has been issued for Germany.
Acceptance by a vehicle expert is not required (except when
installing the low chassis kit). The general operating permit
(ABE) must be kept in the vehicle.
The Mover XT / XT2 complies with other requirements of
EC Directives and Standards (see Declaration of conformity).
When installing the Mover XT / XT2, the technical and admin-
istrative regulations of the country of first registration of the
vehicle must be observed.
Any modifications made to the device, or the use of any spare
parts or functionally significant accessories other than original
Truma parts, or failure to comply with the contents of the op-
erating and installation instructions invalidates the warranty
and precludes any liability claims. This will also invalidate the
operating permit for the equipment.

Tools and facilities required

To install the Mover XT / XT2 you need:
– 8 mm, 10 mm,13 mm and 17 mm socket wrenches, ring
spanners or open-jawed spanners
– Allen key 4
– Torque wrenches (3.5 – 50 Nm)
– Cable cutter / crimping tool
– Electric drill / screwdriver / keyhole saw, diameter 25 mm
– 2-tonne trolley jack and suitable support trestles
– Adequate lighting

Minimum installation dimensions

A distinction is made between L-profile and U-profile
frames as shown in the illustration.
Caravan floor
L-profile
Figure 6
Installation is only possible on caravans with the following
dimensions.
U-profile
EN
23