Ryobi Expand-It RXPR01 Traduction Des Instructions Originales page 5

■
Do not let familiarity gained from frequent use of
machines allow you to become complacent and ignore
tool safety principles. A careless action can cause
severe injury within a fraction of a second.
■
Keep handles and grasping surfaces dry, clean and
free from oil and grease. Slippery handles and grasping
surfaces do not allow for safe handling and control of
the tool in unexpected situations.
WARNING
If the product is dropped, suffers heavy impact or begins
to vibrate abnormally, immediately stop the product and
inspect for damage or identify the cause of the vibration.
Any damage should be properly repaired or replaced by
an authorised service centre.
FOR ASSEMBLING WITH ELECTRIC-DRIVEN POWER
HEAD ONLY
■
Electrical power should be supplied via a residual
current device (RCD) with a tripping current of not more
than 30 mA
■
If you need to use an extension cable ensure it is
suitable for outdoor use and has a current capacity
sufficient to supply your tool. Check it before every use
for damage. Always uncoil it during use because coiled
cables can overheat.
■
If the power cable becomes damaged, it must be
replaced before using.
PRUNER SAFETY WARNINGS
■
Never use the pruner when there is a possibility of
thunderstorm or lightning. Store the pruner and/or the
power cables safely indoors.
■
Ensure all guards, handles are properly fitted and are
in good condition.
■
Do not start using the product until you have a clear
work area, secure footing, and a planned retreat path
away from the falling branches or limbs.
■
Beware of the emission of lubricant mist and saw dust.
Wear mask or respirator if required.
■
Always hold the pruner with both hands when operating
it. Use one hand to firmly grasp the front hand grip. Use
the other hand to grasp the rear handle and operate
the product.
■
Hold the power tool by insulated gripping surfaces only,
because the saw chain may contact hidden wiring.
Saw chains contacting a "live" wire may make exposed
metal parts of the power tool "live" and could give the
operator an electric shock.
■
Do not modify your product in any way or use it to power
any attachments or devices not recommended by the
manufacturer for your pruner.
■
Your pruner comes with a harness. You must use it
whilst operating the pruner. It will assist you to control
the drop of the pruner after the cut is completed. It will
also help support the weight of the machine during use
and whilst moving between pruning positions.
■
Identify the quick release mechanism and practice
using it before you start using the machine. Its
correct use may prevent serious injury in the case of
an emergency. Never wear additional clothing over
the harness or otherwise restrict access to the quick
release mechanism.
■
Before starting the tool, make sure the saw chain is not
contacting any object.
■
An incorrectly tensioned chain can jump off the guide
bar and could result in serious injury. Check each use
and frequently, especially a new chain.
■
To reduce the risk of injury associated with moving
parts, always stop the product, and disconnect from
power supply (if applicable), make sure all moving parts
have come to a stop before:
●
cleaning or clearing a blockage
●
leaving the product unattended
●
installing or removing attachments
●
checking, maintenance or working on the machine
■
Kickback may occur when the nose or tip of the guide
bar touches an object, or when the wood closed in and
pinches the saw chain in cut. Tip contact in some cases
may cause a sudden reverse reaction, kicking the
guide bar up and back towards the operator. Pinching
the saw chain along the top of the guide bar may push
the guide bar rapidly back towards the operator. Either
of these reactions may cause you to lose control of
the machine which could result in serious personal
injury. Do not rely exclusively upon the safety devices
built into your machine. As a pruner user, you should
take several steps to keep your cutting jobs free from
accident or injury. Kickback is the result of tool misuse
and/or incorrect operating procedures or conditions and
can be avoided by taking proper precautions as given
below:
●
With a basic understanding of kickback, you can
reduce or eliminate the element of surprise. Sudden
surprise contributes to accidents.
●
Make sure that the area in which you are cutting
is free from obstructions. Do not let the nose of
the guide bar contact branch, limb or any other
obstruction while you are operating the unit.
●
Maintain a firm grip, with both hands on the
machine and position your body and arm to allow
you to resist kickback forces. Kickback forces can
be controlled by the operator, if proper precautions
are taken. Do not let go of the pruner.
●
Do not overreach. This helps prevent unintended tip
contact and enables better control of the pruner in
unexpected situations.
●
Only use replacement bars and chains specified by
the manufacturer. Incorrect replacement bars and
chains may cause chain breakage and/or kickback.
●
Sharpening the chain safely is a skilled task.
Therefore the manufacturer strongly recommends
that a worn or dull chain is replaced with a new
one, available from your authorised Ryobi service
centre. The part number is available in the product
specification table in this manual.
■
Do not use on a ladder or unstable support. Always cut
with both feet on solid ground to prevent being pulled
off balance.
EN
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
BG
UK
English | 3