Storage And Transport; Maintenance And Servicing; Maintenance And Cleaning - Bosch GTS 10 XC Professional Notice Originale

46 | English
Setting
– Loosen the hex socket screws (77) using the hex key
(37) provided.
– Carefully move the parallel guide (8) until it touches the
saw blade along its entire length.
– Hold the parallel guide in this position and push the
clamping handle (51) down again.
– Retighten the hex socket screws (77).
Adjusting the clamping force of the parallel guide
The clamping force of the parallel guide (8) can deteriorate
after frequent use.
– Tighten the adjusting screw (31) until the parallel guide
can be securely fixed to the saw table again.
Adjusting the magnifying glass of the parallel guide (see
figure P)
– Bring the power tool into the work position.
– Remove the blade guard (6).
– Move the parallel guide (8) from the right until it touches
the saw blade.
Checking
The marking in the magnifying glass (68) must be in line with
the 0 mm mark on the scale (1).
Setting
– Loosen the screw (78) using a cross-headed screwdriver
and align the marking along the 0 mm mark.
Adjusting the level of the table insert (see figure Q)
Checking
The front side of the table insert (32) must lie flush with or a
little below the saw table; the rear must lie flush with or a
little above the saw table.
Setting
– Remove the table insert (32).
– Use the hex key (37) to set the correct level of the four
adjusting screws (79).

Storage and transport

Storing tool elements (see figures R1–R6)
You can attach certain tool elements to the power tool to
store them.
– Detach the additional parallel guide (52) from the parallel
guide (8).
– Place all loose components of the tool in their storage
compartments on the housing (see the following table).
Fig- Tool element Storage compartment
ure
R1 Protective cover Place in the recess on the
bracket (22) and secure using
the clamping lever (49)
R2 "Additional parallel Clip into the brackets (80)
guide" fastening set
(39)
R2 Dust extraction ad- Slide into the holding clips (81)
apter (41)
1 609 92A 5B8 | (15.07.2019)
Fig- Tool element Storage compartment
ure
R3 Unused saw blades Place in the saw blade storage
compartment (82) and fasten
the cover (14) above it with the
securing nut (12)
R3 Ring spanner (15) Place in the saw blade storage
compartment (82) and fasten
the cover (14) above it with the
securing nut (12)
R3 Push stick (13) Attach with the securing nut
(12)
R4 Hex key (37) Slide into the brackets (83)
R4 Parallel guide (8) Place in the parallel guide stor-
age compartment (36)
R5 Angle guide (3) Slide into the holding clips (23)
R6 Additional parallel Place in the additional parallel
guide (52) guide storage compartment and
secure with the holding clip
(84)
Transporting the power tool
Before transporting the power tool, the following steps must
be carried out:
– Bring the power tool into the transport position (see
"Transport position", page 42).
– Remove all accessories that cannot be securely fitted to
the power tool.
If possible, transport unused saw blades in an enclosed
container.
– Slide the saw table expansion (11) in fully and push the
clamping handle (18) down to secure it in place.
– Slide the saw table extension (10) all the way in and
tighten the locking screws (38) on the guide bars (24).
– Wrap the power cable around the cable holder (42).
– Use the carrying handles (4) to lift or transport the tool.
Only use the transport devices to transport the power
u
tool and never the protective devices.

Maintenance and servicing

Maintenance and cleaning

Pull the plug out of the socket before carrying out any
u
work on the power tool.
In order to avoid safety hazards, if the power supply cord
needs to be replaced, this must be done by Bosch or by an
after-sales service centre that is authorised to repair Bosch
power tools.
Cleaning
To ensure safe and efficient operation, always keep
u
the power tool and the ventilation slots clean.
Remove dust and chippings after each operation with a
paintbrush.
Bosch Power Tools