Storage And Transport; Maintenance And Service; Maintenance And Cleaning - Bosch GTS 10 J Professional Notice Originale

OBJ_BUCH-1325-004.book Page 36 Tuesday, September 13, 2016 1:06 PM
36 | English
Adjusting the Parallelism of the Parallel Guide
(see figure W)
– Bring the power tool into the working position.
– Tilt the blade guard 6.x toward the rear to the stop.
– Loosen the clamping handle 35 of the parallel guide and
slide it until it touches the saw blade.
Checking:
The parallel guide 10 must touch the saw blade over the com-
plete length.
Adjusting:
– Loosen the hex socket screws 71 using the supplied hex
key 21.
– Carefully move the parallel guide 10 until it touches the
saw blade over the complete length.
– Hold the parallel guide in this position and press the clamp-
ing handle 35 down again.
– Retighten the hex socket screws 71.
Adjusting the Tension Force of the Parallel Guide
The tensioning force of the parallel guide 10 can decrease af-
ter frequent usage.
– Tighten the adjustment screw 70 until the parallel guide
can be firmly affixed on the saw table again.
Adjusting the Lens of the Parallel Guide (see figure W)
– Bring the power tool into the working position.
– Tilt the blade guard 6.x toward the rear to the stop.
– Move parallel guide 10 from the right until it touches the
saw blade.
Checking:
The mark of lens 27 must be in a line with the 0° mark of scale
1.
Adjusting:
– Loosen screw 62 using a cross-head screwdriver and align
the clearance indicator alongside the 0° mark.
Adjusting the Level of the Insert Plate (see figure X)
Checking:
The front side of the insert plate 24 must be flush with or
somewhat lower than the saw table; the rear side must be
flush with or somewhat above the saw table.
Adjusting:
– Remove the insert plate 24.
– Adjust the correct level of the four adjusting screws 63
with the hex key 64.

Storage and Transport

Storing Product Features (see figures Y1–Y6)
For storage purposes, certain product features can be se-
curely fastened to the power tool.
– Loosen auxiliary parallel guide 37 from parallel guide 10.
– Attach all loose tool parts to their storage locations on the
housing. (see Table)
1 609 92A 2C1 | (13.9.16)
Figure Product Feature Storage Location
Y1 Blade guard 6.x Insert into the recess of fixture
33 and tighten with clamping
lever 8.1 or clamping screw 8.2
Y2 "Auxiliary parallel Clip into the holders 65
guide" fastening
kit 38
Y2 Extraction adapter Insert into retaining clamp 66
32
Y3 Ring spanner 22 Fasten in tool depot with fas-
tening nut 67
Y3 Push stick 23 Mount onto fastening nut 67
and fasten by turning
Y4 Parallel guide 10 Turn guide around and hang it
into the guide rails from below;
tighten clamping handle 35
Y5 Hex key 21 Insert into holders 68
Hex key 64
Y5 Angle stop 3 Insert into retaining clamp 69
Y6 Auxiliary parallel Insert into retaining brackets
guide 37 30 (short side goes on top; long
side toward the rear)
Carrying the Power Tool
Before transporting the power tool, the following steps must
be carried out:
– Bring the machine into the transport position
(see "Transport Position", page 33).
– Remove all accessories that cannot be mounted firmly to
the power tool.
If possible, place unused saw blades in an enclosed con-
tainer for transport.
– Slide the saw-table extension 14 completely inward and
press tensioning lever 15 downward to lock it.
– Wind the mains cable around the cable holder 29.
– For lifting or transport, use the recessed handles 4 or the
carrying handle 13.
 When transporting the power tool, use only the trans-
port devices and never use the protective devices.
 The power tool should always be carried by two per-
sons in order to avoid back injuries.

Maintenance and Service

Maintenance and Cleaning

 Before any work on the machine itself, pull the mains
plug.
If the replacement of the supply cord is necessary, this has to
be done by Bosch or an authorized Bosch service agent in or-
der to avoid a safety hazard.
Cleaning
– For safe and proper working, always keep the power tool
and its ventilation slots clean.
– Remove dust and chips after each working procedure by
blowing out with compressed air or with a brush.
Bosch Power Tools