Storage And Transport - Bosch GTS 10 J Professional HEAVY DUTY Notice Originale

26 | English
– Measure the distance between the saw blade and the
guide groove again.
The two measured distances must be identical.
Setting
– Loosen the hex socket screws (66) at the front beneath
the saw table and the hex socket screws (67) at the rear
beneath the saw table using the hex key (22) provided.
– Carefully move the saw blade until it lies parallel with the
guide groove (5).
– Retighten all screws (66) and (67).
Adjusting the saw table spacing indicator (see figure L)
– Position the parallel guide on the right of the saw blade.
Move the parallel guide until the marking in the magnify-
ing glass (28) shows 26 cm on the lower scale.
To secure it in place, push the clamping handle (41) back
down.
– Pull the clamping handle (16) all the way up and pull the
saw table expansion (14) out as far as possible.
Checking
The upper scale (2) of the spacing indicator (58) must show
the same value as the marking in the magnifying glass (28)
on the lower scale (2).
Setting
– Pull the saw table expansion (14) out fully.
– Loosen the screw (68) with a cross-headed screwdriver
and align the spacing indicator (58) along the 26 cm
mark on the upper scale (2).
Adjusting the parallelism of the parallel guide (see figure
M)
– Bring the power tool into the work position.
– Remove the blade guard (6).
– Loosen the clamping handle (41) of the parallel guide and
move it until it touches the saw blade.
Checking
The parallel guide must touch the saw blade along its entire
length.
Setting
– Loosen the hex socket screws (69) using the hex key
(22) provided.
– Carefully move the parallel guide until it touches the saw
blade along its entire length.
– Hold the parallel guide in this position and push the
clamping handle (41) down again.
– Retighten the hex socket screws (69).
Adjusting the clamping force of the parallel guide
The clamping force of the parallel guide can deteriorate
after frequent use.
– Tighten the adjusting screw (25) until the parallel guide
can be securely fixed to the saw table again.
Adjusting the magnifying glass of the parallel guide (see
figure M)
– Bring the power tool into the work position.
– Remove the protective cover (6).
1 609 92A 6YX | (01.09.2021)
– Move the parallel guide from the right until it touches the
saw blade.
Checking
The marking in the magnifying glass (28) must be in line with
the 0 mm mark on the scale (2).
Setting
– Loosen the screw (70) using a cross-headed screwdriver
and align the marking along the 0 mm mark.
Adjusting the level of the table insert (see figure N)
Checking
The front side of the table insert (26) must lie flush with or a
little below the saw table; the rear must lie flush with or a
little above the saw table.
Setting
– Remove the table insert (26).
– Use the hex key (22) to set the correct level of the four
adjusting screws (71).

Storage and transport

Storing tool elements (see figures O1–O5)
You can attach certain tool elements to the power tool to
store them.
– Detach the additional parallel guide (43) from the parallel
guide .
– Place all loose components of the tool in their storage
compartments on the housing (see the following table).
Fig- Tool element Storage compartment
ure
O1 Protective cover (6) Place in the recess on the
bracket (34) and secure using
the clamping lever (39)
O1 Anti-kickback Press the push buttons (48) to-
pawls (9) (Country gether and allow them to engage
version in the hole of the bracket (74)
3 601 M30 5C2 )
O2 "Additional parallel Clip into the brackets (72)
guide" fastening
set (44)
O2 Dust extraction ad- Slide into the holding clips (73)
apter (33)
O3 Ring spanner (23) Secure in the storage compart-
ment using the securing
nut (75)
O3 Push stick (24) Suspend using the securing
nut (75) and slide to secure
O4 Parallel guide Turn around, suspend from be-
low in the guide rails and secure
the clamping handle (41)
O5 Hex key (22) Slide into the brackets (76)
Hex key (21)
O5 Angle guide (3) Slide into the holding clips (77)
Bosch Power Tools