Dust/Chip Extraction - Bosch GTS 10 J Professional HEAVY DUTY Notice Originale

ted correctly and all the conditions necessary to ensure
smooth operation must be met.
If the protective devices or any parts become damaged, you
must have them properly repaired or replaced by an author-
ised service centre.
Fitting individual components
– Carefully remove all parts included in the delivery from
their packaging.
– Remove all packing material from the power tool and the
accessories provided.
– Make sure that you remove the packaging material be-
neath the motor block.
The following parts of the tool are attached directly to the
housing: Push stick (24), ring spanner (23), hex key (22)
and (21), parallel guide (10), angle guide (3), dust extrac-
tion adapter (33), additional parallel guide (43) with fasten-
ing set (44), protective cover (6).
– If you require one of these parts, remove it carefully from
its storage location.
Positioning the riving knife (see figures a1–a2)
Note: If necessary, clean all parts to be fitted before you po-
sition them.
– Turn the crank (19) clockwise as far as possible so that
the saw blade (27) is in the highest possible position
above the saw table.
– Loosen the clamping lever (35).
or
country version 3 601 M30 5C2 : Loosen the hex socket
screws (36) with the hex key (22).
– Slide the riving knife (8) towards the clamping lever (35)
until it can be pulled upwards.
– Pull the riving knife all the way up until it is positioned ex-
actly over the centre of the saw blade.
– Allow both pins (37) to engage in the lower bore holes in
the riving knife and then retighten the clamping lever (35)
or the hex socket screws (36).
Fitting the table insert (see figure b)
– Hook the table insert (26) into the rear recesses (38) of
the tool chamber.
– Guide the table insert down.
– Press down on the table insert until it engages in the front
of the tool chamber.
The front side of the table insert (26) must lie flush with or a
little below the saw table; the rear must lie flush with or a
little above the saw table.
Fitting the protective cover (see figures c1–c2)
Note: Only fit the protective cover when the riving knife is in
the top position directly over the centre of the saw blade
(see figure a2). Do not fit the protective cover when the riv-
ing knife is in the bottom position (position when delivered/
position for sawing grooves) (see figure a1).
– Loosen the clamping lever (39) and remove the protect-
ive cover (6) from the bracket (34).
Bosch Power Tools
– Hold the saw blade guard (upper metal rail) of the pro-
tective cover (6) with one hand, while using the other
hand to move the clamping lever (39) up.
– Push the guide pin (40) backwards into the groove on the
riving knife (8).
– Move the protective cover (6) down until the saw blade
guard (upper metal rail) is parallel with the surface of the
saw table (7).
– Push the clamping lever (39) down. The clamping lever
must be felt and heard to engage; the protective cover (6)
must be securely and safely fitted.
Always check that the blade guard can move properly
u
before use. Do not use the power tool if the blade
guard cannot move freely and does not close immedi-
ately.
Fitting the parallel guide (see figure d)
The parallel guide (10) can be positioned on either the left or
the right of the saw blade.
– Loosen the clamping handle (41) of the parallel guide
(10). This lightens the load on the V guide (42).
– First insert the parallel guide with the V guide into the
guide groove (11) of the saw table. Then position the par-
allel guide in the front guide groove (1) of the saw table.
The parallel guide can now be moved freely.
– To secure the parallel guide, push the clamping handle
(41) down.
Fitting the additional parallel guide (see figure e)
To saw narrow workpieces and bevel angles, you must fit
the additional parallel guide (43) on the parallel guide (10).
The additional parallel guide can be fitted on the left or right
of the parallel guide (10) as required.
Use the "additional parallel guide" fastening set (44) (two
fastening screws, two washers, two wing nuts) for fitting the
guide.
– Slide the fastening screws through the lateral holes on the
parallel guide (10).
– The heads of the screws are used to guide the additional
parallel guide.
– Slide the additional parallel guide (43) over the heads of
the fastening screws.
– Place the washers on the fastening screws and tighten the
screws using the wing nuts.
Fitting the angle guide (see figure f1-f2)
– Push the rail (45) of the angle guide (3) into one of the
guide grooves (5) provided in the saw table.
To make it easier to position long workpieces, the angle
guide can be extended with the profile rail (29).
– If necessary, fit the profile rail on the angle guide using
the fastening set (46).

Dust/chip extraction

The dust from materials such as lead paint, some types of
wood, minerals and metal can be harmful to human health.
Touching or breathing in this dust can trigger allergic reac-
English | 21
1 609 92A 6YX | (01.09.2021)