Bosch GTS 10 J Professional HEAVY DUTY Notice Originale page 23

– Place the new saw blade on the mounting flange (53) of
the tool spindle (52).
Note: Use sufficiently large saw blades. The radial clearance
between the saw blade and the riving knife must not exceed
3−8 mm (max.).
When mounting the saw blade, ensure that the cutting
u
direction of the teeth (direction of the arrow on the
saw blade) matches the direction of the arrow on the
riving knife.
– Fit the clamping flange (51) and the clamping nut (49).
– Turn the clamping nut (49) using the ring spanner (23)
while pulling the spindle locking lever (50) until it en-
gages.
– Tighten the clamping nut by turning it clockwise.
– Reinsert the table insert (26).
– Refit the protective cover (6).
– In addition for country version 3 601 M30 5C2 :
Refit the anti-kickback pawls (9).
Operation
Pull the plug out of the socket before carrying out any
u
work on the power tool.
Transport position and work position of the saw
blade
Transport position
– Remove the protective cover (6), remove the table insert
(26) and place the riving knife (8) in the bottom position.
Reinsert the table insert (26).
– Turn the crank (19) anticlockwise until the teeth of the
saw blade (27) lie below the saw table (7).
– Push the saw table expansion (14) in fully.
Push the clamping handle (16) down. This fixes the saw
table expansion in place.
Work position
– Position the riving knife (8) in the top position directly
over the centre of the saw blade, insert the table insert
(26) and fit the protective cover (6).
– Turn the crank (19) clockwise until the top teeth of the
saw blade (27) are approx. 3−6 mm above the work-
piece.
Setting mitre and bevel angles
To ensure precise cuts, the basic settings of the power tool
must be checked and adjusted as necessary after intensive
use.
Setting Bevel Angles (saw blade) (see figure A)
The bevel angle can be set between -2° and 47°.
– Loosen the locking lever (17) by turning it anticlockwise.
Note: When the locking lever is fully loosened, gravity
causes the saw blade to tilt into a position that corresponds
to approximately 30°.
Bosch Power Tools
– Pull or push the hand wheel (18) along the slotted link un-
til the angle indicator (54) shows the required bevel
angle.
– Hold the hand wheel in this position and retighten the
locking lever (17).
For quick and precise setting of the standard bevel
angles of 0° and 45°, there are pre-set stops ((62)),((65)).
Setting mitre angles (angle guide) (see figure B)
The mitre angle can be set between 60° (left-hand side) and
60° (right-hand side).
– Loosen the locking knob (56) if it is tightened.
– Turn the angle guide until the angle indicator (57) shows
the required mitre angle.
– Retighten the locking knob (56).
Extending the saw table
The free end of long and heavy workpieces must have some-
thing placed underneath it or be supported.
Saw table expansion (see figure C)
The saw table expansion (14) increases the width of the saw
table (7) on the right to a maximum of 625 mm.
– Pull the clamping handle (16) for the saw table expansion
all the way up.
– Pull out the saw table expansion (14) to the required
length.
– Push the clamping handle (16) down. This fixes the saw
table expansion in place.
Adjusting the parallel guide
The parallel guide can be positioned on either the left (black
scale) or the right (silver scale) of the saw blade. The mark-
ing in the magnifying glass (28) indicates the set distance of
the parallel guide to the saw blade on the scale (2).
Position the parallel guide on the required side of the saw
blade.
Adjusting the parallel guide
when the saw table is not pulled out
– Loosen the clamping handle (41) of the parallel guide .
Move the parallel guide until the marking in the magnify-
ing glass (28) indicates the desired distance from the saw
blade.
When the saw table is not pulled out, the lower marking
on the silver scale applies (2).
– To secure it in place, push the clamping handle (41) back
down.
Adjusting the parallel guide
when the saw table is pulled out (see figure D)
– Position the parallel guide on the right of the saw blade.
Move the parallel guide until the marking in the magnify-
ing glass (28) shows 26 cm on the lower scale.
To secure it in place, push the clamping handle (41) back
down.
– Pull the clamping handle (16) for the saw table expansion
all the way up.
English | 23
1 609 92A 6YX | (01.09.2021)