Contraindications - Johnson & Johnson Biosense Webster ThermoCool SmartTouch Mode D'emploi

English
T C
HERMO OOL
Deflectable Tip Catheter
Caution: Federal (U.S.A.) law restricts this device to sale by or
on the order of a physician.

STERILE. Sterilized with ethylene oxide gas.

For single use only.

Do not resterilize.

Do not use if the package is open or damaged.
Catheter Description
The Biosense Webster T
Deflectable Tip Catheter is a multi-electrode luminal catheter with a deflectable
tip designed to facilitate electrophysiological mapping of the heart and to transmit
radiofrequency (RF) current to the catheter tip electrode for ablation purposes.
The catheter shaft measures 7.5 F with 8 F ring electrodes. For ablation, the
catheter is used in conjunction with an RF generator and a dispersive pad
(indifferent electrode). The catheter has force-sensing technology that provides a
real-time measurement of contact force between the catheter tip and the heart
wall.
The catheter has a high-torque shaft with a uni-directional deflectable tip section
containing an array of electrodes which includes a 3.5 mm tip dome. All of the
electrodes may be used for recording and stimulation purposes. The tip
electrode serves to deliver RF current from the RF generator to the desired
ablation site. The tip electrode and ring electrodes are made from a noble metal.
The catheter incorporates a thermocouple temperature sensor that is embedded
in the 3.5 mm tip electrode. Tip deflection is controlled at the proximal end by a
handpiece in which a piston slides; a thumbknob on the piston controls piston
travel. When the thumbknob is pushed forward, the tip is deflected (curved).
When the thumbknob is pulled back, the tip straightens. The high-torque shaft
also allows the plane of the curved tip to be rotated to facilitate accurate
positioning of the catheter tip at the desired site. Currently, the available curves
for the uni-directional version of the
Biosense Webster T
Deflectable Tip Catheter include D, F and J.
At the proximal end of the catheter, a saline input port with a standard Luer fitting
terminates from the open lumen. This saline port serves to permit the injection of
normal saline to irrigate the tip electrode. During ablation, heparinized normal
saline is passed through the internal lumen of the catheter and through the tip
electrode, to irrigate and cool the ablation site as well as the electrode tip. An
irrigation pump should be used to control the saline irrigation. The catheter
interfaces with standard recording equipment and a compatible RF generator via
accessory extension cables with the appropriate connectors.
This catheter features a location sensor embedded in the tip section that
transmits location and contact force information to the C
System. An appropriate reference device is required for location reference
position purposes. For use in mapping procedures and for information on
appropriate reference devices, and for further description of the operation of the
®
C 3 System, refer to the User Manual for your C
ARTO
System.
Indications
The Biosense Webster T
Deflectable Tip Catheter is indicated for use in cardiac electrophysiological
mapping (stimulation and recording) and, when used in conjunction with a
radiofrequency generator, for cardiac ablation.
The Biosense Webster T
Deflectable Tip Catheter provides a real-time measurement of contact force
between the catheter tip and heart wall, as well as location information when
®
used with C
ARTO

Contraindications

Do not use this device:
1. If the patient has had a ventriculotomy or atriotomy within the preceding
eight weeks because the recent surgery may increase the risk of perforation.
2. In the patient with a myxoma or an intracardiac thrombus as the catheter
could precipitate an embolus.
3. In patients with prosthetic valves as the catheter may damage the
prosthesis.
4. In the coronary vasculature due to risk of damage to the coronary arteries.
5. In patients with an active systemic infection because this may increase the
risk of cardiac infection.
6. Via the transseptal approach in a patient with an interatrial baffle or patch
because the opening could persist and produce an iatrogenic atrial shunt.
7. Via the retrograde trans-aortic approach in patients who have had aortic
valve replacement.
Warnings
1. Do not use excessive force to advance or withdraw the catheter when
resistance is encountered. The contact force reading is for information only
and is not intended to replace standard handling precautions.
2. The catheter must be warmed up as specified prior to use. If the catheter
has not reached a steady state condition, there is potential for a zero-offset
drift to occur which could result in an inaccurate contact force reading.
3. Always zero the contact force reading following insertion into the patient or
when moving the catheter from one chamber of the heart to another. Ensure
the catheter is not in contact with heart tissue prior to zeroing. Refer to the
User Manual for your C
contact force reading.
4. The contact force reading might become inaccurate if the contact force
sensor (located between the first and second ring electrode) comes into
close proximity with a ferrous material, such as the braided shaft of another
catheter. If extreme fluctuations in force are observed, ensure the catheter's
contact force sensor is not in close proximity with another catheter's shaft,
check zero on the catheter and, if necessary, remove and inspect the
catheter.
5. To ensure proper operation of the contact force sensor, the first two ring
electrodes of the catheter tip must protrude from the distal tip of the guiding
sheath.
6. Do not use the temperature sensor to monitor tissue temperature. The
temperature sensor located within the tip section of the catheter does not
reflect either electrode-tissue interface or tissue temperature due to the
cooling effects of the saline irrigation of the electrode. The temperature
displayed on the RF generator is the temperature of the cooled electrode,
not tissue temperature. The temperature sensor is used to verify that the
irrigation flow rate is adequate. Before initiating the application of RF
current, a decrease in electrode temperature confirms the onset of saline
irrigation of the ablation electrode. Monitoring the temperature from the
electrode during the application of RF current ensures that the irrigation flow
rate is being maintained.
4
WARNING: This is a controlled proprietary and confidential document. Verify revision is current prior to use.
AVISO: Este es un documento controlado, confidencial, y con derechos reservados. Revisar si es la revision mas actualizada.
®
S T
MART OUCH
C
HERMO OOL
®
C S
HERMO OOL MART
C
HERMO OOL
C
HERMO OOL
3 Navigation System.
®
3 System for instructions on how to zero the
ARTO
™
Diagnostic/Ablation
® ™
S T Diagnostic/Ablation
MART OUCH
™
T Diagnostic/Ablation
OUCH
ARTO
® ™
S T Diagnostic/Ablation
MART OUCH
® ™
S T Diagnostic/Ablation
MART OUCH
®
3 Navigation
ARTO
®
3 Navigation
M-5276-692A