Ryobi RBV26 Manuel D'utilisation page 18

Deutsch (Übersetzung der originalen Anleitungen)
Racing ...................................................91.6 / 95.5 dB(A)
Idling .......................................................78.9 / 81.4dB(A)
Equivalent A-weight emission sound pressure level.........
...............................................................84.4 / 88.0 dB(A)
Uncertainty of sound level measurement .............3 dB(A)
vibration value at handle according to EN 15503:2009
Annex B
Blower mode(Front handle/ rear handle)
Racing .......................................................9.9 / 20.4 m/s
Idling ..........................................................8.7 / 11.9 m/s
Equivalent vibration total value ..................9.7 / 19.4 m/s
Uncertainty of vibration measurement .................1.5 m/s
KNOW YOUR BLOWER/VACUUM
See Figures 1a - 1b.
The safe use of this product requires an understanding of
the information on the tool and in this operator's manual
as well as a knowledge of the project you are attempting.
BLOWER TUBE AND NOZZLES
The blower tube can be assembled and installed on the
blower without using any tools.
POSITIVE SWITCHES
The product is equipped with positive switches. The unit
will only run if both the metal contacts are inserted into
the positive switches. This reduces the risk of accidental
contact with rotating parts.
CRUISE CONTROL
The cruise control feature allows the user to operate the
blower without holding the throttle trigger. To slow the
en gine, simply push the cruise control lever forward.
HIGH VELOCITY NOZZLE WITH WET LEAF SCRAPER
The high velocity nozzle is great for wet sticky leaves.
It allows you to scrape off wet leaves or debris while
operating the blower.
MOTOR
The blower has a powerful 26cc engine with sufficient
power to handle tough blowing and vacuuming jobs.
START EASY™
The Start Easy™ feature allows easier and quicker
starting.
THROTTLE TRIGGER
The blower can be operated at any speed between idle
and full throttle.
VACUUM / SILENCER
Converting the blower to a vacuum/silencer is simple and
can be done using a cross head screwdriver.
English (Original instructions)
VACUUM BAG
The vacuum bag attaches to the blower easily by using
the vacuum bag adaptor.
VACUUM HANDLE
This feature allows user to perform vacuuming duties
comfortably.
VACUUM TUBES
The vacuum tubes can be installed on the blower using a
cross head screw driver.
2
ASSEMBLY
2
2
2
UNPACKING
This product requires assembly.
n
n
n
ASSEMBLING THE BLOWER TUBES
See Figure 2.
n
n
n
n
n
INSTALLING THE VACUUM BAG
See Figures 3 - 4.
n
16 16
Carefully remove the product and any accessories
from the box. Make sure that all items listed in the
packing list are included.
WARNING:
Do not use this product if any parts on the
Packing List are already assembled to your
product when you unpack it. Parts on this
list are not assembled to the product by the
manufacturer and require customer installation.
Use of a product that may have been
improperly assembled could result in serious
personal injury.
Inspect the product carefully to make sure no
breakage or damage occurred during shipping.
Do not discard the packing material until you have
care fully inspected and satisfactorily operated the
product.
Insert one end of the lower tube into one end of the
upper tube.
Align raised tabs on blower housing outlet to the
slots on the upper tube; slide together and tighten
securely by twisting; press slider plate into positive
switch's slot to allow the positive switch to engage
and be ready to work. Check tightness after initial
use and retighten if needed.
Close the inlet cover and tighten the screw on the
cover, making sure the metal contact is inserted into
the positive switch.
Connect the nozzle to the lower blower tube.
To remove the blower tube, pull out the slider from
the positive switch, then rotate the tubes to remove
them from the blower housing outlet.
Unzip the vacuum bag and place the adaptor inside
as shown. Push the vacuum bag adaptor through the