Technical Data - REMS Cento Notice D'utilisation

eng

1. Technical data

Use for the intended purpose
WARNING
REMS Cento and REMS DueCento are intended for the purpose of cutting and deburring the inside and outside of pipes.
All other uses are not for the intended purpose and are therefore prohibited.
1.1. Scope of Supply
REMS Cento Basic: Pipe cutting machine, ring spanner size 27/17, instruction manual.
REMS DueCento Basic: Pipe cutting machine, ring spanner size 27/17, 2 height adjustable pipe rests, feed lever, spring plug, instruction manual.
1.2. Article numbers
Pipe cutting machine
REMS cutting wheel Cu-INOX for pipes of the press fitting systems of
stainless steel, copper, carbon steel
REMS cutting wheel Cu especially for pipes of the press fitting systems of copper
REMS cutting wheel St for steel pipes, cast pipes (SML)
REMS cutting wheel C-SF especially for pipes of the press fitting systems/push fitting
systems of carbon steel, simultaneously produces a chamfer
REMS cutting wheel V, s 10, for plastic and composite tubes, wall thickness s ≤ 10 mm 845051
REMS cutting wheel P, s 21, for plastic and composite tubes, wall thickness s ≤ 21 mm
Base frame
Rollers INOX (set) of tubular stainless steel
Roller insert for cutting pipes Ø 40 – 100 mm
Ring spanner size 27/17
REMS Herkules 3B, material rest with tripod
REMS Herkules Y, material rest with clamping device
Height adjustable pipe rest Ø 100 – 225 mm
Height adjustable pipe rest Ø 40 – 100 mm
REMS Jumbo, folding workbench
REMS REG 10 – 54 E, outside/inside pipe deburrer
REMS REG 28 – 108, inside pipe deburrer
REMS CleanM, machine cleaner
1.3. Area of application
Stainless steel pipes, copper pipes, composite tubes,
Carbon steel pipes of the press fitting systems
Steel pipes DIN EN 10255 (DIN 2440)
Cast pipes (SML) DIN 19522
Plastic tubes SDR 11, composite tubes
Wall thickness, copper pipes, cast pipes (SML)
Wall thickness plastic/composite tubes
1.4. Speed
Cutting wheel idle speed
1.5. Electrical data
230 V ~; 50 – 60 Hz; 1,200 W; 5,7 A. Fuse (mains) 10 A (B), intermittent mode S3 20% (AB 2/10 min), protective insulated, radio interference suppressed, or
110 V ~; 50 – 60 Hz; 1,200 W; 11,4 A. Fuse (mains) 20 A, intermittent mode S3 20% (AB 2/10 min), protective insulated, radio interference suppressed.
1.6. Dimensions
L×W×H:
1.7. Weight
without safety foot switch
1.8. Noise information
Acoustic pressure level
Acoustic power level
Acoustic pressure level
1.9. Vibrations
Weighted rms value of acceleration
The specified vibration emission value was measured according to a standard test method and can be used for comparison with another device. The specified vibra-
tion emission value can also be used for an initial estimation of the cut-out.
CAUTION
The vibration emission value may differ from the specified value during actual use of the pipe cutting machine depending on the manner in which the pipe cutting
machine is used. Depending on the actual conditions of use (intermittent mode) , it may be necessary to define safety measures to protect the operator.
2. Start-up
2.1. Electrical connection
WARNING
Caution: Mains voltage present! Before connecting the pipe cutting machine,
check whether the voltage given on the rating plate corresponds to the mains
voltage. On building sites, in a wet environment or for similar types of applica-
tion, only operate the pipe cutting machine on the mains via a 30 mA fault
current protection (FI switch). Observe the cross-section necessary for the
output of the pipe cutting machine when using an extension cable.
2.2. Installing the pipe cutting machine
REMS Cento
Fasten the pipe cutting machine e.g. to REMS Jumbo (Fig. 1) (Art. No. 120200)
or to the base frame (Fig. 2) (Art. No. 849315) with 4 or 2 M8 screws. Make
REMS Cento
845000
845050
845053
845052
845055
849315
845110
849112
120100
120130
120200
113835
113840
140119
REMS Cento
Ø (8) 22 – 108 mm
DN (10) 20 – 100; (⅜") ¾ – 4"
DN 40 – 100 mm
Ø (10) 25 – 110 mm
≤ 4.5 mm
≤ 10.0 mm
115 rpm
REMS Cento
250×300×250 mm (10"×12"×14") 260×430×515 mm (10.2"×16.9"×20.3")
17.8 kg (39 lb)
L = 87 dB
pA
L = 98 dB
wa
L = 100 dB
pc peak
K = 3 dB
< 2.5 m/s²
K = 1.5 dB
sure that there is enough room for the pipe cutting machine, REMS Jumbo/
base frame and the pipe to be cut. Longer pipes must be supported by REMS
Herkules (Fig. 2) (Art. No. 120100) or REMS Herkules Y (Art. No. 120130), on
both sides of the pipe cutting machine if necessary. Move the cutting wheel
drive (1) forwards by turning the feed lever (6) until the pipe to be cut (5) can
be placed on the rollers (3). To set the height of REMS Herkules, place the pipe
to be cut in the centre of the rollers (3) of the pipe cutting machine. Do not allow
the pipe (5) to knock against the cutting wheel (2), the cutting wheel could
otherwise be damaged. Open the clamping lever of REMS Herkules, lower the
pipe rest of REMS Herkules, place REMS Herkules under the pipe near the
pipe cutting machine, lift the pipe rest against the pipe and tighten the clamping
lever. Place the preset REMS Herkules under the end of the pipe. Place other
material rest(s) between the pipe cutting machine and the pipe end(s) if neces-
sary to reduce untrue running of the pipe.
eng
REMS DueCento
845005
845050
845053
845052
845055
845051
845057
845060
849112
845220
845230
140119
REMS DueCento
Ø (54) 108 – 225 mm
DN (50) 100 – 150; (1½") 4 – 6"
DN (40) 100 – 200 mm
Ø (50) – 110 mm
≤ 5.0 mm
≤ 21.0 mm
115 rpm
REMS DueCento
36.4 kg (80.2 lb)
L = 87 dB
pA
L = 98 dB
wa
L = 100 dB
pc peak
K = 3 dB
< 2.5 m/s²
K = 1.5 dB