Safety Instructions For Batteries; Technical Data - REMS Nano Notice D'utilisation

eng
Safety instructions for Batteries
WARNING
Read all safety warnings and all instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
● Only use the battery in the REMS power tool. Only then is the battery safe
from dangerous overloading.
● Only use original REMS batteries with the voltage specified on the rating
plate. Using other batteries can lead to injuries and risk of fire due to exploding
batteries.
● Use the battery and the rapid charger only in the specified operating
temperature range.
● Only recharge REMS batteries in the REMS rapid charger. There is a risk of
fire if an unsuitable battery charger is used.
● Charge the battery to full capacity with the rapid charger before using for
the first time. Batteries are delivered partly charged.
● Insert the battery into the battery compartment straight and without force.
There is a risk of bending the battery contacts and damaging the battery.
● Protect the batteries against heat, sunlight, fire, moisture and wet. There is
a risk of explosion and fire.
● Do not use the batteries in areas where there is a risk of explosion and in
the vicinity of inflammable gases, solvents, dust, fumes, liquids for example.
There is a risk of explosion and fire.
● Do not open the battery or modify its construction. There is a risk of explosion
and fire due to short-circuiting.
● Do not use batteries with damaged housings or damaged contacts. Damage
to or improper use of the battery can cause fumes to escape. The fumes can
irritate the respiratory tracts. Let in fresh air and consult a doctor in case of
symptoms.
● Fluid can leak from the battery when used improperly. Do not touch the
fluid. Leaking fluid can cause skin irritation and burns. Rinse off immediately
with water in case of contact. Also consult a doctor if the fluid gets into the eyes.
● Observe the safety instructions on the battery and the rapid charger.
● Keep unused batteries away from paper clips, coins, keys, nails, screws
or other small metal objects which could cause bridging of the contacts.
There is a risk of explosion and fire due to short-circuiting.
● Remove the battery before stowing/storing the power tool for long periods
of time. Protect the battery contacts against short­circuiting, e.g. with a cap.
● Do not throw defective batteries in the normal household waste. Hand the
defective batteries over to an authorised REMS contract service workshop or a
recognised disposal company. Observe the national regulations.
Explanation of symbols
WARNING
Danger with a medium degree of risk which could result in death
or severe injury (irreversible) if not heeded.
CAUTION Danger with a low degree of risk which could result in minor injury
(reversible) if not heeded.
NOTICE
Material damage, no safety note! No danger of injury.
Read the operating instructions before use
REMS Nano complies with protection class I
REMS Akku-Nano and rapid charger comply
with protection class Il
Environmentally friendly disposal
CE conformity mark
1. Technical Data
Use for the intended purpose
WARNING
REMS Nano and REMS Akku-Nano are intended for the purpose of cutting pipes.
All other uses are not for the intended purpose and are prohibited.
1.1. Scope of Supply
REMS Nano: Electric pipe cutting machine (without cutting wheel),
single open-ended wrench size 8, operating instructions,
carrying case.
REMS Akku-Nano: Cordless pipe cutting machine (without cutting wheel),
Li-Ion battery, Li-Ion/Ni-Cd rapid charger, single
open-ended wrench size 8, operating instructions,
carrying case.
1.2. Article numbers
REMS Nano
REMS Akku-Nano
REMS High-Power-Battery Li-Ion 10.8 V, 1.3 Ah
Rapid-charger Li-Ion/Ni-Cd 230 V, 50 – 60 Hz, 65 W
REMS cutting wheel Cu-INOX
REMS cutting wheel V
REMS Herkules 3B
8
REMS Herkules Y
REMS Jumbo
REMS Jumbo E
Carrying case
REMS CleanM
1.3. Application Area
REMS Nano, REMS Akku-Nano:
Pipes of pressfitting systems made of
● stainless steel, C-steel (not jacketed)
● semi-hard and hard copper
● composite pipes
1.4. Speed
REMS Nano, REMS Akku-Nano:
Idle speed of cutting wheel
1.5. Electrical Data
REMS Nano:
230 V~; 50 – 60 Hz; 130 W
Fuse (mains) 10 A (B), cut-out operation S3 20 % AB 2/10 min,
radio interference suppressed, protection class I, PE conductor as of
machine no. 3650
REMS Akku-Nano: 10,8 V =, 16 A, 270 W
Rapid-charger
Li-Ion/Ni-Cd Input
Output 10,8 – 18 V – ---
Input
Output 10,8 – 18 V – ---
1.6. Dimensions
REMS Nano:
L × W × H:
REMS Akku-Nano:
L × W × H:
1.7. Weights
REMS Nano
REMS Akku-Nano drive machine without battery
1.8. Noise Data
Workplace-related emission
value
1.9. Vibrations
Weighted effective value of the acceleration
The indicated weighted effective value of acceleration has been measured
against standard test procedures and can be used by way of comparison with
another device. The indicated weighted effective value of acceleration can also
be used as a preliminary evaluation of the exposure.
CAUTION
The indicated weighted effective value of acceleration can differ during operation
from the indicated value, dependent on the manner in which the device is used.
Dependent upon the actual conditions of use (periodic duty) it may be necessary
to establish safety precautions for the protection of the operator.
2. Start-up
2.1. Electrical Connection
WARNING
Caution: Mains voltage present! Before connecting the electric pipe cutting
machine or the rapid charger, check whether the voltage given on the rating
plate corresponds to the mains voltage. Only use sockets/extension leads with
a functioning protected earth contact for REMS Nano. On building sites, in a
wet environment, indoors and outdoors or under similar installation conditions,
only operate the electric pipe cutting machine on the mains with a fault current
protected switch (FI breaker) which interrupts the power supply as soon as the
leakage current to earth exceeds 30 mA for 200 ms.
Rechargeable batteries
NOTICE
Always hold the battery (9) upright when inserting it in the drive unit or the rapid
charger. If inserted at an angle it can cause damage to the contacts and result
in a short circuit which damages the battery.
Total discharging by undervoltage
The Li-Ion batteries may not drop below a minimum voltage because otherwise
the battery could be damaged by "total discharge". The cells of the REMS Li-Ion
battery are delivered pre-charged to approx. 40 %. Therefore the Li-Ion batteries
844000
must be charged before use and recharged regularly. Failure to observe this
844001
regulation of the cell manufacturer can lead to damage to the Li-Ion battery by
844510
total discharging.
571560
844050
Total discharging due to storage
844051 If a relatively low charged Li-Ion battery is stored, self discharging can lead to
120120
total discharge damage of the battery after longer storage. Li-Ion batteries must
230 V~; 50 – 60 Hz; 65 W, all-insulated,
interference-suppressed
100 – 120 V~; 50 – 60 Hz; 65 W, all-insulated,
interference-suppressed
405 × 90 × 103 mm (15.9"× 3.5"× 4")
408 × 88 × 105 mm (16"× 3.4"× 4.1")
L = 78 dB L = 67 dB L = 87 dB K = 3 dB
wA pA pC, peak
1.2 m/s² K = 1.5 m/s²
eng
120130
120200
120240
574436
140119
Ø 12 – 28 mm
Ø 10 – 35 mm
Ø 10 – 40 mm
130 min‫¹־‬
1.9 kg (4.2 lb)
2.0 kg (4.4 lb)