General Power Tool Safety Warnings - REMS Cento Notice D'utilisation

g
Translation of the Original Instruction Manual
Fig. 1– 8
2 Cutting wheel
3 Rollers
4 Holes for stand
8 Spindle

General Power Tool Safety Warnings

WARNING
Read all safety warnings and all instructions. Failure to follow the warnings and
Save all warnings and instructions for future reference.
The term "power tool" in the warnings refers to your mains-operated (corded) power
tool or battery-operated (cordless) power tool.
1) Work area safety
a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b)
may ignite the dust or fumes.
c) Keep children and bystanders away while operating a power tool. Distrac-
tions can cause you to lose control.
2) Electrical safety
a)
b)
if your body is earthed or grounded.
c)
tool will increase the risk of electric shock.
d)
parts. Damaged or entangled cords increase the risk of electric shock.
e)
outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric
shock.
f)
protected supply. Use of an RCD reduces the risk of electric shock.
3) Personal safety
a)
power tools may result in serious personal injury.
b)
equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protec-
tion used for appropriate conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch is in the off-position before
tool
tools that have the switch on invites accidents.
d)
wrench or a key left attached to a rotating part of the power tool may result in
personal injury.
e)
better control of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair and
caught in moving parts.
g)
tion can reduce dustrelated hazards.
4) Power tool use and care
a) Do not force the power tool. Use the correct power tool for your application.
The correct power tool will do the job better and safer at the rate for which it was
designed.
b) Do not use the power tool if the switch does not turn it on and off. Any power
tool that cannot be controlled with the switch is dangerous and must be repaired.
c)
storing power tools. Such preventive safety measures reduce the risk of starting
the power tool accidentally.
d) Store idle power tools out of the reach of children and do not allow persons
9 Spring plug
Ø 100 – 225 mm
12 REMS REG 28-108
13 REMS REG 10-54 E
14 Roller insert for cutting pipes
Power tools create sparks which
Unmodi-
There is an increased risk of electric shock
Water entering a power
A moment of inattention while operating
Protective
This enables
Loose clothes, jewellery or long hair can be
Use of dust collec-
tool. Power tools are dangerous in the hands of untrained users.
e)
accidents are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with
sharp cutting edges are less likely to bind and are easier to control.
g)
Use of the power tool for operations different from those intended
could result in a hazardous situation.
h)
not allow for safe handling and control of the tool in unexpected situations.
5) Service
a)
is maintained.
WARNING
Read all safety warnings and all instructions. Failure to follow the warnings and
Save all warnings and instructions for future reference.
-
and the cutting wheel are subject to heavier wear by too high feeding pressure
and can be damaged. At too high feeding pressure, the ends of the pipe to be
cut are pressed further inwards causing constriction of the cross section. Pipes
made of brittle material, e.g. cast pipes, can be fractured or broken by too high
feeding pressure.
This reduces off-centre running of the pipes and the cut
-
are not straight causes imbalance and the pipe or pipe rest can fall over. The
pipe can also slip off the material or pipe rest, the pipe cutting machine can move
and the cutting wheel can be damaged. Danger of injury.
been locked as described in 2.2. If the feed lever is not locked there is a danger
that the feed lever (6) will come away from the spindle (8). REMS DueCento can
then fall over or fall off. Danger of injury.
cutting. Danger of injury.
regularly.
customer service workshop in case of damage.
-
may only use the pipe cutting machine when they are over 16, when this is
necessary for their training and when they are supervised by a trained operative.
The pipe cutting machine is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities or lack of experience and
knowledge unless they have been given supervision or instruction concerning
the use of the pipe cutting machine by a person responsible for their safety.
Children must be supervised to ensure that they do not play with the pipe cutting
machine.
A
WARNING Danger with a medium degree of risk which could result in
CAUTION Danger with a low degree of risk which could result in minor
NOTICE
Read the operating manual before starting
Slippery handles do
This will ensure that the safety of the power tool
The pipe cutting machine
There is a risk
Cutting pipes that
Apprentices
g
Many