Publicité
Les langues disponibles
Les langues disponibles
FR
EN DE
ES
EN
FR
DE
ES
DE
FR
EN
ES
ES
FR
EN
DE
When the temperature is above 10°C, pull the starter
■
IT
FR
EN
DE
ES
grip until the engine attempts to start, but no more
than 3 times. When the temperature is below 10°C,
FR
EN
DE
ES
IT
pull the starter grip until the engine attempts to start,
but no more than 5 times.
FR
EN
DE
ES
IT
Push choke lever to run position. Pull starter grip
■
until engine runs.
FR
EN
DE
ES
IT
Note: Allow the saw to run in this position 15-30
FR
EN
DE
ES
IT
seconds, depending upon the temperature.
Depress the trigger release and squeeze and release
■
FR
EN
DE
ES
IT
the throttle trigger to return the engine to idle after a
total run time of at least 30 seconds.
FR
EN
DE
ES
IT
CAuTION:
FR
EN
DE
ES
IT
Failure to release throttle when chain brake lever is in
the brake position will result in serious damage to the
FR
EN
DE
ES
IT
unit. Never squeeze and hold the throttle trigger while the
chain brake is in the brake position.
FR
EN
DE
ES
IT
To Start a Warm Engine:
FR
EN
DE
ES
IT
Turn on the ignition switch.
■
FR
EN
DE
ES
IT
Make sure the chain brake is in the run position by
■
pulling back on the lever/hand guard.
FR
EN
DE
ES
IT
Keep choke lever on run position.
■
Pull starter grip until engine runs, but no more than 5
FR
EN
DE
ES
IT
■
times. If engine does not start after 5 pulls, use cold
FR
EN
DE
ES
IT
engine starting procedure.
Squeeze and release the throttle trigger to return the
■
FR
EN
DE
ES
IT
engine to idle.
FR
EN
DE
ES
IT
STOPPINg THE ENgINE
See Figures 7 and 14.
FR
EN
DE
ES
IT
Release the throttle trigger and let the engine return to
FR
EN
DE
ES
IT
idle. To stop the engine, move the ignition switch to the
stop (0) position. Do not put the chainsaw on the ground
when the chain is still moving. For additional safety, set the
chain brake when the saw is not in use.
In the event that the ignition switch will not stop the saw,
pull the choke lever out to the fully extended position (Full
Choke) and engage the chain brake to stop the engine.
If the ignition switch will not stop the saw when set to the
stop position, have the ignition switch repaired before
using the chainsaw again to prevent unsafe conditions or
serious injury.
NOTE: When you are finished using the saw, always
relieve tank pressure by loosening, then retightening, the
chain lubricant and fuel caps. Allow the engine to cool
before storing.
AdjuSTINg IdLE SPEEd
See Figure 15.
If the engine starts, runs, and accelerates, but will
■
IT
PT
NL
SV
DA NO
IT
PT
NL
SV
DA NO
IT
PT
NL
SV
DA NO
IT
PT
NL
SV
DA NO
PT
NL
SV
DA NO
PT
NL
SV
DA NO
NL
PT
SV
DA NO
SV
PT
NL
DA NO
DA
PT
NL
SV
NO
PT
NL
SV
DA
PT
NL
SV
DA NO
PT
NL
SV
DA NO
PT
NL
SV
DA NO
PT
NL
SV
DA NO
PT
NL
SV
DA NO
PT
NL
SV
DA NO
PT
NL
SV
DA NO
PT
NL
SV
DA NO
PT
NL
SV
DA NO
PT
NL
SV
DA NO
PT
NL
SV
DA NO
PT
NL
SV
DA NO
PT
NL
SV
DA NO
FI
HU CS RU
FI
HU CS RU
FI
HU CS RU
English
FI
HU CS RU
not idle, turn the idle speed screw "t" clockwise to
FI
HU CS RU
increase idle speed to 2600~3600 rpm.
If the chain turns at idle, turn the idle speed screw
■
FI
HU CS RU
"t" counter clockwise to reduce the idle RPM and
stop the chain movement. If the saw chain still moves
FI
HU CS RU
at idle speed, contact an authorised service centre
for adjustment and discontinue use until the repair is
FI
HU CS RU
E
made.
WARNINg:
NO
FI
HU CS RU
THE SAW CHAIN SHOULD NEVER TURN AT
FI
HU CS RU
IDLE. Serious personal injury may result from
the saw chain turning at idle.
FI
HU CS RU
PuLL ANd PuSH
HU
See Figure 16.
FI
CS RU
The reaction force of the saw is always opposite to the
CS
FI
HU
RU
direction the chain is moving. Thus, the operator must
be ready to control the PULL when cutting on the bottom
RU
FI
HU CS
edge of the bar and the PUSH when cutting along the
top edge.
FI
HU CS
RU
Note: The chainsaw has been fully factory tested. It is
FI
HU CS
RU RO
normal to find some slight lubricant residue on the saw.
FI
HU CS
RU RO
kICkBACk PRECAuTIONS
See Figures 17 - 18.
FI
HU CS
RU RO
Rotational kickback occurs when the moving chain
contacts an object at the Kickback Danger Zone of the
FI
HU CS
RU RO
guide bar. The result is a lightning-fast reverse reaction,
which kicks the guide bar up and back towards the
FI
HU CS
RU RO
operator. This reaction can cause loss of control, which
can result in serious injury.
FI
HU CS
RU RO
PREPARINg FOR CuTTINg
FI
HU CS
RU RO
PROPER gRIP ON HANdLES
See Figure 19.
FI
HU CS
RU RO
See General Safety Rules for appropriate safety
equipment.
Wear non-slip gloves for maximum grip and
■
protection.
Hold the saw firmly with both hands. Always keep
■
your left hand on the front handle and your right hand
on the rear handle so that your body is to the left of
the chain line.
WARNINg:
Never use a left-handed (cross-handed) grip or
any stance that would place your body or arm
across the chain line.
Maintain a proper grip on the saw whenever the
■
engine is running. The fingers should encircle
the handle and the thumb is wrapped under the
handlebar. This grip is least likely to be broken by a
kickback or other sudden reaction of the saw. Any
grip in which the thumb and fingers are on the same
side of the handle is dangerous because a slight kick
of the saw can cause loss of control.
38
RO PL
SL
HR ET
RO PL
SL
HR
ET
RO PL
SL
HR
ET
RO PL
SL
HR
ET
RO PL
SL
HR
ET
RO PL
SL
HR
ET
RO PL
SL
HR
ET
RO PL
SL
HR
ET
RO PL
SL
HR
ET
RO PL
SL
HR
ET
RO PL
SL
HR
ET
RO PL
SL
HR
ET
RO PL
SL
HR
ET
RO PL
SL
HR
ET
RO
PL
SL
HR
ET
PL
SL
HR
ET
SL
PL
HR
ET
HR
PL
SL
ET
ET
PL
SL
HR
PL
SL
HR
ET
PL
SL
HR
ET
PL
SL
HR
ET
PL
SL
HR
ET
LT
LV
SK BG
LT
LV
SK BG
LT
LV
SK BG
LT
LV
SK BG
LT
LV
SK BG
LT
LV
SK BG
LT
LV
SK BG
LT
LV
SK BG
LT
LV
SK BG
LT
LV
SK BG
LT
LV
SK BG
LT
LV
SK BG
LT
LV
SK BG
LT
LV
SK BG
LT
LV
SK BG
LT
LV
SK BG
LT
LV
SK BG
LT
LV
SK BG
LT
LV
SK BG
LT
LV
SK BG
LV
LT
SK BG
SK
LT
LV
BG
BG
LT
LV
SK
Publicité
