Engine Radiator Fin Cleaning Check; Engine Coolant Level Check; Engine Fuel Filter Replacement - Nilfisk Advance RS 501 Instructions D'utilisation

ENGINE RADIATOR FIN CLEANING CHECK

1. Empty the hopper (12, Fig. G); if it contains a small quantity of waste, it is not necessary to dump it.
2. Drive the machine on a solid and level ground, then engage the parking brake (7, Fig. E).
3. Lift the hopper (12, Fig. G), according to the procedure shown in the relevant paragraph.
4. Turn off the engine, by turning the ignition key (17, Fig. D) counterclockwise, to the end of stroke, then remove it.
5. Open the right and left doors (16 and 4, Fig. G) by releasing the fasteners (17 and 5) with the supplied key.
6. Remove the lifted hopper locking pins (9, Fig. F) from the housings (10), and place them into the holes (11).
7. Empty the dust control system water tanks (17 and 21, Fig. F) according to the instructions shown in the relevant paragraph.
8. On both sides of the machine, loosen the screws (19 and 23, Fig. F), and open the right and left tanks (17 and 21) outwards.
WARNING!
Open the tanks (17 and 21, Fig. F) outwards, only if they are empty: each tank contains 120 kg of water
approximately.
9. Check the radiator fi n cleaning as shown in the diesel engine Manual.
10. Perform steps 3, 4, 5, 6 and 8 in the reverse order.
11. If necessary, fi ll the dust control system water tanks according to the procedure shown in Before Start-Up paragraph.

ENGINE COOLANT LEVEL CHECK

1. Empty the hopper (12, Fig. G); if it contains a small quantity of waste, it is not necessary to dump it.
2. Drive the machine on a solid and level ground, then engage the parking brake (7, Fig. E).
3. Lift the hopper (12, Fig. G), according to the procedure shown in the relevant paragraph.
4. Turn off the engine, by turning the ignition key (17, Fig. D) counterclockwise, to the end of stroke, then remove it.
5. Open the right door (16, Fig. G) by releasing the fasteners (17) with the supplied key.
6. Remove the lifted hopper locking pins (9, Fig. F) from the housings (10), and place them into the holes (11).
WARNING!
The coolant line is pressurized; do not perform any check until the engine has cooled down and, even if the
engine is cold, the tank plug (1, Fig. AL) must be opened with extreme care.
7. Check that the coolant level in the tank (2, Fig. AL) is between the minimum and maximum marks, as shown in the diesel
engine Manual. If necessary, unscrew the plug (1) and top up.
Coolant components:
• 50% of AGIP antifreeze
• 50% of water
After top up, tighten the plug (1).
8. Perform steps 3 to 6 in the reverse order.

ENGINE FUEL FILTER REPLACEMENT

1. Empty the hopper (12, Fig. G); if it contains a small quantity of waste, it is not necessary to dump it.
2. Drive the machine on a solid and level ground, then engage the parking brake (7, Fig. E).
3. Lift the hopper (12, Fig. G), according to the procedure shown in the relevant paragraph.
4. Turn off the engine, by turning the ignition key (17, Fig. D) counterclockwise, to the end of stroke, then remove it.
5. Open the left and right doors (4 and 16, Fig. G) by releasing the fasteners (5 and 17) with the supplied key.
6. Remove the lifted hopper locking pins (9, Fig. F) from the housings (10), and place them into the holes (11).
7. Empty the dust control system water tanks (17 and 21, Fig. F) according to the instructions shown in the relevant paragraph.
8. Remove the screw (23, Fig. F) and open the left tank (21) outwards.
WARNING!
Open the tanks (17 and 21, Fig. F) outwards, only if they are empty: each tank contains 120 kg of water
approximately.
9. Replace the fuel fi lter as shown in the diesel engine Manual.
10. Perform steps 3, 4, 5, 6 and 8 in the reverse order.
11. If necessary, fi ll the dust control system water tanks according to the procedure shown in Before Start-Up paragraph.
INSTRUCTIONS FOR USE
RS 501 33019745(2)2009-12
ENGLISH
39