Campingaz 4 RBS EXS Serie Utilisation Et Entretien page 9

- tighten the G 1/2 threaded nut on the hose onto the
barbecue inlet connector and the M20x1.5 threaded
nut onto the regulator output connector following the
instructions supplied with the flexible hose.
- use 2 spanners to tighten the flexible pipe on the
appliance's inlet connector:
•
a 14 mm spanner to immobilise the appliance's inlet
connector.
•
an adjustable spanner to tighten the nut on the flexible
pipe.
- use a spanner to tighten the nut on the flexible pipe on
the regulator.
- check for leaks following the instructions in paragraph f).
Check that the flexible hose stretches out normally without
twisting or pulling and does not come into contact with the
hot sides of the barbecue. It should be replaced when
the expiry date on the hose is passed or whenever it is
damaged or develops surface cracks.
Do not pull or pierce the hose. keep away from any parts
of the barbecue that get hot.
Belgium, Luxembourg, United Kingdom, Ireland,
Portugal, Spain, Italy, Croatia, Greece, Netherlands,
Czech Republic, Slovakia,
Norway, Sweden, Denmark, Finland, Bulgaria, Turkey,
Romania, Poland:
The barbecue is equipped with a circular connector. It
should be used with flexible hose that is suitable for use
with butane and propane gas.
Hose length should not exceed 1.20 meters. It should be
replaced if it is damaged or develops surface cracks or
when so required by national legislation.
Do not pull or pierce the hose. keep away from any parts
of the barbecue that get hot.
Check that the flexible hose stretches out normally, without
twisting or pulling.
Switzerland, Germany, Austria:
The barbecue should be used with flexible tubing that is
suitable for use with butane and propane gas.
Tubing length should not exceed 1.50 meters. It should
be replaced if it is damaged or develops surface cracks
or when so required by national legislation. Do not pull or
pierce the tubing.
keep away from any parts of the barbecue that get hot.
Check that the flexible hose stretches out normally, without
twisting or pulling.
Flexible tubing connection: to connect the tubing to the
connector on the barbecue, tighten the nut on the tubing
firmly but without excess force using the two wrenches
provided:
- no. 14 wrench to tighten the connector
- no. 17 wrench to tighten the nut on the tubing
Hungary, Slovenia,
9
e) LID
Handle the lid carefully, especially during operation. do
not lean over the base.
f) CHECKING FOR GAS LEAKS
1) Work outside, away from all sources of ignition. do not
smoke.
2) Make sure the control knobs are in the "off" (O) position.
3) Connect the flexible tubing to the connector and
barbecue as described in part d).
4) Fit the regulator onto the gas cylinder in accordance
with its instructions.
5) Use a gas leak solution to test for leaks. Important:
never use a naked flame to check for gas leaks.
6) apply the solution to the connections cylinder/regulator/
hose/apparatus (the control knobs should remain
closed: « OFF » position (O)). Open the gas cylinder
valve.
7) bubbles in the gas leak solution indicate that there are
gas leaks.
8) The leak can be stopped by tightening any hose
connection or replacing any faulty component. the
barbecue must not be used until the leak is stopped.
9) Close the valve on the gas cylinder.
Important:
Never use a naked flame to check for gas leaks.
Check for leaks at least once per year and each time the
gas cylinder is replaced.
g) PRIOR TO USE
Never use the barbecue until the instructions have been
read carefully and understood. also, make certain that:
- there are no leaks
- the venturi tubes are not blocked (example: spider
webs).
Venturi tube openings
- the hose does not touch any components which may get
hot.
GB