Grillo Climber CL 7.13 Mode D'emploi Et Maintenance page 11

TECHNICAL DATA
ENGINE:
7.13 - B&S VANGUARD 13,5 hp (10 kW) OHV, single-cylinder, internal combustion, 4-stroke, AVS synchro-
balanced series.
7.16 - B&S VANGUARD OHV 16 hp (13 kW), twin-cylinder, internal combustion, 4-stroke series.
7.21 - B&S VANGUARD OHV 21 hp (15.5 kW), twin-cylinder, internal combustion, 4-stroke series.
HOURLY CONSUMPTION: 3 lt/h – 7.13 / 3.5 lt/h – 7.16 / 3.8 lt/h – 7.21.
STARTING SYSTEM: electric, with battery 12V.
GEARBOX: hydrostatic transmission.
DIFFERENTIAL: with locking device.
CLUTCH: for PTO with V-belt.
GROUND SPEED: from 0 to 9 km/h with continuous variation and reverse from 0 to 4 km/h.
TYRES front: 13x5.00-6; rear: 16x 6.50-8.
BRAKE: front emergency brake; rear parking brake.
OPERATOR SEAT: sprung und adjustable, fitted with roll bar.
CUTTING DECK: side/rear discharge.
CUTTING SYSTEM: single rotating blade.
CUTTING WIDTH: 780 mm – 7.13 / 850 mm – 7-16 &7.21
BLADE SPEED: 70 m/sec.
CUTTING HEIGTH: from 35 mm to 85 mm, 6 cutting positions and 1 for travelling.
WORK CAPACITY: 4800 m 2 /h (indicative) – 7.13 / 6.000 m 2 /h (indicative) – 7.16 & 7.21
STEERING RADIUS: 485 mm.
FUEL TANK: 7 lt, RESERVE: 1 lt.
TOWING BAR: as a standard.
IMPLEMENTS: garden wheels set.
SIZES: W900xL1895xH975mm.
WEIGHT: • 225 kg – 7.13 / • 235 kg – 7.16 / • 245 kg – 7.21.
PUTTING THE MACHINE INTO SERVICE
1) Check that the machine has not been damaged in transit.
2) Check the oil levels of the engine, hydrostatic transmission and final drive.
3) Check the tyre pressure:
4) 1 BAR front wheels 13 x 5.00-6
5) 1.2 BAR rear wheels 16 x 6.50-8.
6) Check the battery voltage; it must be at least 12 Volts. Charge if necessary.
7) IMPORTANT!!! During assembly take care not to reverse the polarity of the battery.
8) Fix the steering wheel taking care the key is properly inserted and the screw is tight enough (tightening torque
2 KgF.m [20 N.m]).
9) Fit the muffler, the rear bumper and the roll bar.
RUNNING IN - CAUTION!!
Change the engine oil and filter after the first 5 working hours.
Check that there are no oil leaks or slack screws, especially those which fix the blade and the steering.
INSTRUCTIONS FOR USE
Before starting up the engine, always check that:
– the travel lever is in the idle position (fig. 3);
– the engine oil level is correct (fig. 4);
– the engine cooling intake grilles are clean (fig. 4);
– air filter is clean (fig. 8).
– the mowing deck is clean;
– the hydraulic motor fins are clean (fig. 5);
– the blades are sharp and firmly fastened in place;
– the screw in the centre of the blade hub is safety tightened (3, fig. 9)
– the oil in the hydraulic axle is at the correct level (fig. 5); the correct level is 12 mm underneath the bottom of
the tank (fig. 6);
Fill the fuel tank using a funnel with very fine filter (4, fig. 10).
Adjust the seat by using the lever fig. 11.
11