Manufacturer's Warranty - REMS Tornado Instructions D'emploi

eng
limiting valve (16), remove the pipe, and check the groove made. To do
so, use the diameter measuring tape or the slide rule at a 90° angle. If ne-
cessary, adjust the stop (17) and repeat the procedure. 1 scale graduation
on the stop plate corresponds to an infeed of approx. 0.4 mm, a complete
revolution is 1.5 mm.
3.3. Support of the material
Pipes and long pipe sections must be supported. Ensure here that the
support keeps the pipe at right angles and parallel to the roll grooving ma-
chine axis.
4. Maintenance
Pull out the mains plug before starting any maintenance and repair work! This
work may only be performed by experts and trained personnel.
4.1. Servicing
Lubricate the roll grooving unit at the lubricating nipple (19) every 40 wor-
king hours. Use REMS transmission grease, article no. 091012.
4.2. Inspection/maintenance
See also the instructions for use of the respective drive machine REMS
Tornado, REMS Gigant, REMS Magnum.
Check the hydraulic oil level regularly. To do so, unscrew the hydraulic
hand pump and hold it with its rear end vertically upward. Open the pres-
sure limiting valve (16), unscrew the oil dipstick (20) in the lid of the con-
tainer, and check the oil level. If necessary, top up with REMS hydraulic
oil, article no. 091026. Always heed the marks on the oil dipstick – do not
pour in too much oil.
Change the hydraulic oil completely at last every 12 months. To do so, tilt
the container to drain off the old oil, which must be disposed of without
harming the environment.
5. Circuit diagrams and equipment list
See the instructions for use of the respective drive machine REMS Tornado,
REMS Gigant, REMS Magnum.
6. Action in Case of Trouble
See also the instructions for use of the respective drive machine REMS Tornado,
REMS Gigant, REMS Magnum.
6.1. Trouble
Incorrect groove dimensions (width or depth).
Cause
Incorrect grooving rollers.
•
Worn grooving rollers.
•
Incorrect feed space selected with setting disc.
•
6.2. Trouble
Machine does not start.
Cause
Emergency-stop not reset.
•
Motor protection switch has responded.
•
Worn or damaged carbon brushes.
•
6.3. Trouble
No grooving roller feed.
Cause
Pressure limiting valve not closed.
•
Too little hydraulic oil in system, system leakage.
•
Feed cylinder defective.
•
6.4. Trouble
Pipe not gripped.
Cause
Grooving rollers worn.
•
Chuck of drive machine not closed.
•
Too little hydraulic oil in system, system leakage.
•
6.5. Trouble
Pipe runs out of the grooving rollers.
Cause
Pipe not aligned axis-parallel with the machine.
•
Grooving rollers worn or defective.
•

7. Manufacturer's Warranty

The warranty period shall be 12 months from delivery of the new product
to the first user but shall be a maximum of 24 months after delivery to the
Dealer. The date of delivery shall be documented by the submission of
the original purchase documents, which must include the date of purchase
and the designation of the product. All functional defects occurring within
the warranty period, which clearly the consequence of defects in produc-
tion or materials, will be remedied free of charge. The remedy of defects
shall not extend or renew the guarantee period for the product. Damage
attributable to natural wear and tear, incorrect treatment or misuse, failure
to observe the operational instructions, unsuitable operating materials, ex-
cessive demand, use for unauthorized purposes, interventions by the Cu-
stomer or a third party or other reasons, for which REMS is not responsible,
shall be excluded from the warranty.
Services under the warranty may only be provided by customer service
stations authorized for this purpose by REMS. Complaints will only be
accepted if the product is returned to a customer service station autho-
rized by REMS without prior interference in an unassembled condition.
Replaced products and parts shall become the property of REMS.
The user shall be responsible for the cost of shipping and returning the
product.
The legal rights of users, in particular the right to claim damages from the
Dealer, shall not be affected. This manufacturer's warranty shall apply only
to new products purchased in the European Union, in Norway or Swit-
zerland.
eng