Appendix A: Emc Information - Philips RESPIRONICS EverFlo Manuel De L'utilisateur

Appendix A: EMC Information

G M
uidanCe and anufaCTurer
use in the electromagnetic environment specified below. The user of this device should make sure it is used in such an
environment.
e T
Missions esT
RF emissions
CISPR 11
RF emissions
CISPR 11
Harmonic emissions
IEC 61000-3-2
Voltage fluctuations/Flicker emissions
IEC 61000-3-3
G M
uidanCe and anufaCTurer
use in the electromagnetic environment specified below. The user of this device should assure that it is used in such an
environment.
i T
MMuniTy esT
Electrostatic Discharge (ESD)
IEC 61000-4-2
Electrical Fast Transient/Burst
IEC 61000-4-4
Surge
IEC 61000-4-5
Voltage dips, short
interruptions and voltage
variations on power supply
input lines
IEC 61000-4-11
Power frequency (50/60 Hz)
magnetic field
IEC 61000-4-8
Note: U
is the a.c. mains voltage prior to application of the test level.
T
' d - e
s eClaraTion
C
oMplianCe
Group 1
Class B
Class A
Complies
' d - e
s eClaraTion
ieC 60601 T
esT
l
evel
±6 kV contact
±8 kV air
±2 kV for power supply lines
±1 kV for input-output lines
±1 kV Line to Line
±2 kV Line to Ground
<5% U
T
(>95% dip in U ) for 0.5 cycle
T
40% U
T
(60% dip in U ) for 5 cycles
T
70% U
T
(30% dip in U ) for 25 cycles
T
<5% U
T
(>95% dip in U ) for 5 sec
T
3 A/m
e
leCTroMaGneTiC Missions
e
leCTroMaGneTiC
The device uses RF energy only for its internal function. Therefore, its
RF emissions are very low and are not likely to cause any interference
in nearby electronic equipment.
The Device is suitable for use in all establishments, including
domestic establishments and those directly connected to the public
low-voltage power supply network that supplies buildings used for
domestic purposes.
i
leCTroMaGneTiC MMuniTy
C l
oMplianCe evel
±6 kV contact
±8 kV air
±2 kV for Power Supply Lines
NA – Device does not have
user I/O lines that are longer
than 3m in length.
±1 kV Line to Line
NA - The device is a Class II
device and does not connect
to earth ground.
<5% U
T
(>95% dip in U ) for 0.5 cycle
T
40% U
T
(60% dip in U ) for 5 cycles
T
70% U
T
(30% dip in U ) for 25 cycles
T
<5% U
T
(>95% dip in U ) for 5 sec
T
3 A/m
EverFlo / EverFlo Q User Manual
:
This device is intended for
e – G
nvironMenT uidanCe
:
This device is intended for
e e
leCTroMaGneTiC nvironMenT
G
uidanCe
Floors should be wood, concrete or ceramic
tile. If floors are covered with synthetic
material, the relative humidity should be at
least 30%.
Mains power quality should be that of a
typical home or hospital environment.
Mains power quality should be that of a
typical home or hospital environment.
Mains power quality should be that of a
typical home or hospital environment. If
the user of the device required continued
operation during power mains interruptions,
it is recommended that the device be
powered from an uninterruptible power
supply or a battery.
Power frequency magnetic fields should be
at levels characteristic of a typical location in
a typical home or hospital environment.
–
17