Foreword; Unpacking; Connection; Important - Dru SAXO Instructions D'installation Et Mode D'emploi

INSTRUCTIONS FOR INSTALLATION

Foreword

Dear Customer,
We would like to thank you for buying this DRU product.
Our products have been designed and produced to meet
the highest possible quality, performance and safety
requirements, allowing you to enjoy years of problem-free
use.
The heater has an enclosed combustion chamber. Its
natural draught draws in the combustion air from outside
through a combined inlet-outlet system.The same natural
draught expels the combustion gasses.
In this booklet you will find instructions for the installation
and use of your new appliance. Please read these
instructions and the manual carefully to familiarize yourself
with the appliance. If you require any further support,
please do not hesitate to contact your supplier.

Unpacking

Once the heater has been unpacked, all packaging should
be disposed of in the regular manner.

Connection

This appliance should be connected by a registered
gasinstaller.

Important

• The chimney breast should be adequately vented.
• The appliance must not be packed or covered in any way
whatsoever.
• Always clean the glass pane before using the gas fire, to
prevent any finger marks or other dirt getting burnt into
the glass.
• This appliance may only be installed using the Ø150/Ø80
flue material supplied by DRU.
• NB: To ensure the ignition works properly, the ignition
wire must come into as little contact as possible with the
metal parts of the heater and should therefore not be
wound round the gas or pilot-light pipes or the
thermocouple.
INSTRUCTIONS FOR INSTALLATION

Type of gas

This appliance can only be used and is only suitable for the
country and the type of gas mentioned on the type
identification tag. Please check that the local gas and
pressure correspond with the specifications on the type
identification tag.The type identification tag is a metal plate
(6), see fig. 1. All regulations regarding gas installation,
including any local regulations, must be observed at all
times. The appliance is to be installed by a registered
gasinstaller.
Important
• Keep curtains and any other flammable materials at least
50cm away form the appliance.
• Caution! Touching the heater when hot can cause burns
and blisters!
• The appliance should be installed and maintained by a
registered gasinstaller.
• Do not install any so-called dust filter on or under the
casing.
• Do not hang wet clothes and towels etc. on the heater to
dry.
• For safety reasons a guard should be placed in front of the
fire at all times.

Positioning the appliance

The appliance has been designed to be built snugly into a
newly built chimney breast, made of incombustible and
heat-resistant material.
If you build a chimney breast made of any material other
than stone (e.g. Promatect), we advise you to use glass
fibre wallpaper rather than plaster. Cracks can form at the
corners of the chimney breast as they are immediately
above one of the hottest parts of the heater.
Allow sufficient space for the depth of the appliance.
The built-in height will depend on how the adjustable feet
are set.The feet can be adjusted to the required length,
and can be fixed with self-drilling screws (7) in the interior,
see fig. 1. Build the chimney breast accurately allowing for
the narrow flange on the inside.
Saxo
Remove the glass window of the combustion chamber and
remove the box of logs and bag of accessories.
To do this, unscrew the 2 socket-head screws on the left
of the glass pane, using the spanner provided. Lift the
window frame out of its hinges.
The magnets are supplied separately.
If you have bought an interior with a side pane on the
right, position the magnets as in fig. 1a (9). If you have an
interior with a side pane on the left, position the magnets
in the exact position.
If you have bought a front for an interior with a window on
the left, and the interior has been assembled with a window
on the right, the interior will first have to be converted.
18