Publicité
Les langues disponibles
Les langues disponibles
INSTRUCTIONS FOR INSTALLATION
correspond with the connector.
• Open the lid.
• Insert 4 penlight batteries (type AA). Make sure they are
the right way round.
• Replace the lid.
• Connect the thermocouple wiring (fig. 23, arrows B)
• Connect the ignition wiring (fig. 23, arrow C)
• Place the remote control receiver in the tray on the
service flap.
• If you are using an adaptor, connect it to the unit
(fig 23, arrow A) and plug the appliance in.
Warning:
Make sure the aerial is not too close to the ignition wire or the
high-voltage transformer (under the cover).This could damage
the receiver (see fig. 3)
correct position of the aerial
1. ignition wire
2. high-voltage transformer
3. aerial
The ignition wire must not be laid along metal elements as
this will weaken the spark.
Make sure the receiver is covered during any building or
finishing work, so that no dust gets in or on it.
Make sure there can be no short circuit between the battery
unit and any metal components of the appliance.
This could damage the remote control (see fig. 2 in the
troubleshooting table)
I.e. the ignition wire must not:
- lie across the receiver (the black box)
- touch or cross the aerial
Replacing the batteries in the receiver
• Open the door from the service flap.
• Take the receiver and open the lid.The batteries are under
that cover.
• Remove the old batteries and insert the new ones, making
sure that the + and – signs on the batteries correspond
with those in the holder.
Inserting or replacing the batteries
in the remote control
• Remove the cover on the back of the remote control.
• Connect a square battery (type 6LR61) to the clip.
• Fit the battery in the holder.
• Replace the cover.
• The temperature is shown on the display in Fahrenheit, press
both buttons for a few seconds and it will change to Celsius.
NB: Do not throw old batteries in the dustbin.
They should be treated as Chemical Waste.
For the optimal functioning and longer useful life of its
appliance, Dru advises the use of Duracell batteries.
1.
3.
2.
fig. 3
OPERATING INSTRUCTIONS
A
OPERATING INSTRUCTIONS
Remote Control - Igniting
Turn button A anti-clockwise to ON.
At the same time, press and hold buttons
you hear a short signal indicating that the ignition process
has begun; now release the buttons.
Continuous signals indicate that the ignition process is
active. A short sound signal (0.2 sec., 1kHz) indicates that
the ignition process has been completed and that there is
sufficient gas flow. Now the appliance will automatically
switch to full load.
Adjustment - Flame Height
In standby mode: Press
Press
to decrease flame height or to set appliance at
pilot flame.
Switching the appliance off
The appliance is switched off using the small 'off' button
on your remote control.
"MAN" Mode - Manual Flame Height Adjustment
1. Press
to turn on the main burner.
2. Press
to increase the flame height.
3. Press
to decrease the flame height or to go to pilot
standby position.
NOTE: While pressing either button a symbol indicating
transmission appears on the display.The
receiver confirms transmission with an acoustic
signal.
Setting °C/24 hour or °F/12 hour Clock
Press OFF and
until display changes from Farenheit/
12 hour clock to Celcius/24 hour clock and vice versa.
Setting the Time
1.The display will flash after either:
a. Installing the battery or
b. Simultaneously pressing the
2. Press
to set the hour and the
3. Press OFF to return to manual mode or simply wait
and it will automatically return to the manual mode.
TEMP MODE - Daytime Temperature
Mode:The room temperature is measured and compared
27
B
fig. 24
and
until
to increase flame height.
and
.
to set the minute.
Saxo
Publicité
Chapitres
Dépannage
