Wilo XI4-OR Série Notice De Montage page 4

English
1 Introduction
1.1 About this document
The language of the original operating instruc-
tions is German. All other languages of these
instructions are translations of the original oper-
ating instructions.
This manual is divided into individual sections,
which are listed in the table of contents. Each
section has a meaningful heading which clearly
describes its content.
A copy of the EC-Declaration of conformity is an
integral part of these installation and operating
instructions.
If a technical modification is made to the designs
named there without our agreement, this decla-
ration loses its validity.
1.2 Personnel qualifications
All personnel who work on or with the product
must be qualified for such work, e.g. electrical
work may only be carried out by a qualified elec-
trician. All personnel must be of legal age.
National accident prevention regulations must
also be observed as a basis by the operating and
maintenance personnel.
It must be ensured that personnel have read
and understood these installation and operating
instructions. If necessary, this manual must be
ordered from the manufacturer in the required
language.
This product is not intended for use by persons
(including children) with reduced physical, sen-
sory or mental capabilities, or lack of experience
and knowledge, unless they have been given
supervision and instruction concerning use of the
product by a person responsible for their safety.
Children should be supervised to ensure that they
do not play with the product.
1.3 Copyright
These installation and operating instructions have
been copyrighted by the manufacturer. These in-
stallation and operating instructions are intended
for use by installation, operating and mainte-
nance personnel. It contains technical regulations
and drawings which may not be reproduced or
distributed, either completely or in part, or used
for purposes of competition, or shared with oth-
ers without the express consent of the manufac-
turer. The illustrations used may differ from the
original and are intended merely as an example
representation of the product.
1.4 Subject to change
The manufacturer reserves the right to make
technical modifications to systems and/or
components. These installation and operating
instructions refer to the motor shown on the title
page.
4
1.5 Warranty
In general, the specifications in the current
"General Terms and Conditions" apply to the
warranty.
You can find these here: www.wilo.com/legal
Any deviations must be contractually agreed and
shall then be given priority.
1.5.1 General
The manufacturer is obliged to correct any de-
fects found in the products it sells, provided that
the defects meet the following requirements:
• The quality defects are caused by the materials
used or the way the product was manufactured or
designed.
• The defects were reported in writing to the man-
ufacturer within the agreed warranty period.
• The product was used only under the intended
operating conditions.
1.5.2 Warranty period
The duration of the warranty period is stipulated
in the "General Terms and Conditions".
Any deviations must be contractually agreed!
1.5.3 Spare parts, add-ons and modifications
Only genuine spare parts from the manufacturer
may be used for repairs, replacements, add-ons
and modifications. Unauthorised attachments and
modifications, or the use of non-genuine parts,
can lead to severe damage to the product and/or
to personal injury.
1.5.4 Maintenance
The prescribed maintenance and inspection
work should be carried out regularly. This work
may only be carried out by qualified, trained and
authorised personnel.
1.5.5 Damage to the product
Damage and malfunctions that endanger safety
must be eliminated immediately and properly
by trained personnel. The product may only be
operated if it is in perfect working order.
In general, repairs should only be carried out by
Wilo customer service!
1.5.6 Exclusion of liability
No warranty is granted and no liability is accepted
for damage to the pump chamber if one or more
of the following points apply:
• Inadequate configuration by the manufacturer
due to insufficient and/or incorrect information
provided by the operator or customer
• Non-compliance with safety instructions and
work instructions as specified in these installation
and operating instructions
• Improper use
• Incorrect storage and transport
• Improper installation/dismantling
• Insufficient maintenance
• Incorrect repairs
• Inadequate construction site or construction work
INTRODUCTION
WILO SE 12-2017 DIN A4