ero electronic LDS Manuel De Service page 13

P14 -Display of the protect parameter P14 -Display of the protect parameter P14 -Display of the protect parameter P14 -Display of the protect parameter P14 -Display of the protect parameter
enabling/disabling. enabling/disabling. enabling/disabling. enabling/disabling. enabling/disabling.
This parameter is available only if P11 is different
from 0.
This parameter allows to enable/disable the
display of the protected parameter during
"operative mode".
OFF = protected parameter cannot be displayed
ON = protected parameter can be displayed
P15 - SMART function enabling/ disabling P15 - SMART function enabling/ disabling P15 - SMART function enabling/ disabling P15 - SMART function enabling/ disabling P15 - SMART function enabling/ disabling
0 = The SMART function is disabled
1 = The SMART function enabling/disabling is
NOT protected by the safety key.
2 = The SMART function enabling/disabling is
protected by the safety key.
P16 - Maximum value of the proportional band P16 - Maximum value of the proportional band P16 - Maximum value of the proportional band
P16 - Maximum value of the proportional band P16 - Maximum value of the proportional band
settable by the SMART function settable by the SMART function settable by the SMART function settable by the SMART function settable by the SMART function
This parameter may be programmed from P17or
P18 value to 99.9.
P17 - Minimum value of the proportional P17 - Minimum value of the proportional P17 - Minimum value of the proportional P17 - Minimum value of the proportional P17 - Minimum value of the proportional
band settable by the SMART function in band settable by the SMART function in band settable by the SMART function in
band settable by the SMART function in band settable by the SMART function in
heating control only. heating control only. heating control only. heating control only. heating control only.
This parameter is present only if P5 is different from
5.
It may be programmed from 1.0% to P16 value.
P18 - Minimum value of the proportional band P18 - Minimum value of the proportional band P18 - Minimum value of the proportional band P18 - Minimum value of the proportional band P18 - Minimum value of the proportional band
settable by the SMART function in heating/ settable by the SMART function in heating/ settable by the SMART function in heating/ settable by the SMART function in heating/ settable by the SMART function in heating/
cooling control only (LHS) cooling control only (LHS)
cooling control only (LHS) cooling control only (LHS) cooling control only (LHS)
This parameter is present only when P5 is equal to
5.
This parameter may be programmed from 1.5% to
P17 value.
lxs-1-0f.pmd 9
P19 - Automatic modification of "relative P19 - Automatic modification of "relative P19 - Automatic modification of "relative P19 - Automatic modification of "relative P19 - Automatic modification of "relative
cooling gain" cooling gain" cooling gain" cooling gain" cooling gain" (LHS)
This parameter is present only when P5 is equal
to 5.
OFF = the SMART function do not not not not modify the
"relative cooling gain" parameter.
ON = the SMART function modify the "relative
cooling gain" parameter.
P20 - Minimum value of integral time settable P20 - Minimum value of integral time settable P20 - Minimum value of integral time settable P20 - Minimum value of integral time settable P20 - Minimum value of integral time settable
by SMART function. by SMART function. by SMART function.
by SMART function. by SMART function.
P20 is programmable from 00.1 (10 seconds) to
02.0 (2 minutes).
P21 = Extension of the anti-reset-wind up P21 = Extension of the anti-reset-wind up P21 = Extension of the anti-reset-wind up P21 = Extension of the anti-reset-wind up P21 = Extension of the anti-reset-wind up
Range: from -30 to +30 % of the proportional
band.
NOTE: a positive value encreases the high limit of NOTE NOTE NOTE NOTE
the anti-reset-wind up (over set point) while a
negative value decreases the low limit of the anti-
reset-wind up (under set point).
The advanced configuration procedure is
completed and the instrument shows " CnF" on the
display.
GB GB GB GB GB 9
16/01/2004, 9.29
not