Residual Risks; Transportation And Storage - Ryobi RBC42FSBO Manuel D'utilisation

instant, and suddenly "thrust" the product away from
the object that was hit. This reaction can be violent
enough to cause the operator to lose control of the
product. Blade thrust may occur without warning if
the blade snags, stalls, or binds. This is more likely to
occur in areas where it is difficult to see the material
being cut.
■ For cutting ease and safety, approach the weeds
being cut from the right to the left. In the event an
unexpected object or woody stock is encountered, this
practice could minimise the blade thrust reaction. Both
hands must be used at all times to control the product.

RESIDUAL RISKS

Even when the product is used as prescribed, it is still
impossible to completely eliminate certain residual risk
factors. The following hazards may arise in use and
the operator should pay special attention to avoid the
following:
■ Contact with cutting means
– Ensure that the blade protectors are fitted when
the product is not in use. Keep hands and feet
away from the blades at all times.
■ Injury caused by vibration
– Always use the right tool for the job, use designated
handles, and restrict working time and exposure.
■ Hearing injury caused by exposure to noise
– Wear hearing protection and limit exposure.
■ Eye injury caused by flying debris
– Wear eye protection at all times.
■ Risk of falling objects
– Wear head protection if there is any risk of falling
objects.
Kickback can occur when using the brushcutter. Ensure
proper control by using both hands on the designated
handles. Read and follow the directions elsewhere in this
manual to help reduce the risk of kickback.
RISK REDUCTION
It has been reported that vibrations from handheld tools
may contribute to a condition called Raynaud's Syndrome.
Symptoms may include tingling, numbness and blanching
of the fi ngers, usually apparent upon exposure to cold.
Hereditary factors, exposure to cold and dampness, diet,
smoking and work practices are all thought to contribute to
the development of these symptoms. There are measures
that can be taken by the operator to possibly reduce the
effects of vibration:
■ Keep your body warm in cold weather. When operating
the product, wear gloves to keep the hands and wrists
warm. It is reported that cold weather is a major factor
contributing to Raynaud's Syndrome.
English (Original instructions)
■ After each period of operation, exercise to increase
■ Ensure that the product is correctly located in a
■ Limit the amount of exposure per day. Take frequent
If you experience any of the symptoms of this condition,
immediately discontinue use and see your physician.
Injuries may be caused or aggravated by prolonged
use of the product. When using any tool for prolonged
periods, ensure you take regular breaks.

TRANSPORTATION AND STORAGE

■ Stop the engine and allow it to cool down before
■ Clean all foreign materials from the product.
■ If a cutting blade is fitted, cover it with the blade
■ Drain all fuel from tank into a container approved for
■ Run the engine until it stops, this will remove all fuel
■ Store the product in a cool, dry, and well-ventilated
■ When transporting the product in a vehicle, secure
■ Never carry or transport the product while the engine
■ Abide all government and local regulations for the
SHORT TERM
■ Stop the engine, and allow it to cool down before
■ Clean all foreign material from the product.
■ Store the product in a cool, dry, and well-ventilated
■ Keep away from corrosive agents such as garden
17
blood circulation.
designated working position before starting the
product.
work breaks.
WARNING
storing or transporting.
protector.
petrol. Remember to properly replace and tighten the
fuel cap.
that could become stale and leave varnish and gum
in the fuel system.
place that is inaccessible to children. Keep away from
corrosive agents, such as garden chemicals and de-
icing salts. Do not store outdoors.
it against movement or falling to prevent injury to
persons or damage to the product.
is running.
safety storage and handling of petrol. Excess fuel
should be used in other 2-cycle engine powered
equipment.
storing.
place that is inaccessible to children.