Dustbane Gladiator 1280 Manuel D'opération page 13

Adjusting the main brush
The main brush makes a major contribution to the efficiency of the whole machine.
Correct adjustment ensures better quality cleaning in shorter times. The machine is Replacing/installing the side brushes
delivered correctly adjusted. The main brush therefore only needs further adjustment
when it becomes worn.
This operation must be performed with the machine switched off and the key removed.
For ease of transport, the side brushes are not installed on the machine when it is delivered.
Proceed as follows to adjust the main brush.
Proceed as follows to install the side brushes.
►
• Unscrew the knob (fig. 19).
►
►
• Turn the adjuster anti-clockwise until the knob fixing hole can be engaged
►
(fig. 19).
►
• Screw the knob back in (fig. 19).
Repeat the above procedure to replace worn side brushes.
Replacing/installing the side brushes
For ease of transport, the side brushes are not installed on the machine when it is
delivered. Proceed as follows to install the side brushes.
30
• Raise the side brush holders (fig. 30).
• Unscrew the screw on the side brush motor shaft (fig. 20).
• Remove the keyway protector.
• Position the brush complete with flange over the motor shaft (fig. 20).
• Fit and tighten the brush locking screw again (fig. 20). Repeat the above
procedure to replace worn side brushes.
Adjusting the side brushes
The side brushes direct dirt and debris towards the centre of the machine. The
most efficient height for this purpose is when the side brushes gently touch
the floor. Proceed as follows to increase or reduce the pressure of the side
brushes on the floor, if necessary.
• Lower the side brushes into work position (fig. 21).
• Loosen the two locking screws under the brush lifting knob
(fig. 22).
• Manually move the brush to the required position.
• Tighten the locking screws again (fig. 22).
• Return the brushes to idle position.
Raise the side brush holders (fig. 30).
Unscrew the screw on the side brush motor shaft (fig. 20).
Remove the keyway protector.
Position the brush complete with flange over the motor shaft (fig. 20).
Fit and tighten the brush locking screw again (fig. 20).
Adjusting the side brushes
Never operate the machine without the side brushes installed.
The side brushes direct dirt and debris towards the centre of the machine. The most efficient height
for this purpose is when the side brushes gently touch the floor. Proceed as follows to increase or
reduce the pressure of the side brushes on the floor, if necessary.
► Lower the side brushes into work position (fig. 21).
► Loosen the two locking screws under the brush lifting knob (fig. 22).
► Manually move the brush to the required position.
► Tighten the locking screws again (fig. 22).
► Return the brushes to idle position.
21
Replacing/installing the suction filter
► Unscrew the knob (fig. 19).
► Turn the adjuster anti-clockwise until the knob fixing hole can be engaged
► Screw the knob back in (fig. 19).
19
! DANGER!
Replacing/installing the side brushes
Replacing/installing the side brushes
20
This operation must be performed with the machine switched off and the k
For ease of transport, the side brushes are not installed on the machine when it is
This operation must be performed with the ma
Proceed as follows to install the side brushes.
For ease of transport, the side brushes are not insta
► Raise the side brush holders (fig. 30).
Proceed as follows to install the side brushes.
► Unscrew the screw on the side brush motor shaft (fig. 20).
► Raise the side brush holders (fig. 30).
► Remove the keyway protector.
► Position the brush complete with flange over the motor shaft (fig. 20).
► Unscrew the screw on the side brush motor
► Fit and tighten the brush locking screw again (fig. 20).
► Remove the keyway protector.
Repeat the above procedure to replace worn side brushes.
► Position the brush complete with flange ove
► Fit and tighten the brush locking screw aga
Repeat the above procedure to replace worn side br
30
GB
30
! WARNING!
22
Operations Manual
! DANGER!
19
! DANGER!
! DANGE
20
30
GB
Gladiator 1280
GB
13