Operation; Gate/Door Operator Setup Examples - LiftMaster Elite Serie Manuel D'installation

Gate/Door Operator Setup Examples

The following are example setups for the gate/door operator. Your specific site requirements may be different. Always setup the operator system to the site
requirements, including all necessary entrapment protection devices.
COMMERCIAL/GENERAL ACCESS: A residential community (more than four homes) having one or more gated entrances/exits, allowing vehicle access
trumps security concerns
COMMERCIAL: Business site where security (gate/door closed) is important
INDUSTRIAL: Large business site where security is required
SETTING
Quick Close switch setting
AC Fail Open switch setting
Low Battery switch setting
Anti-Tail switch setting
Bipart Delay switch setting
Aux Relay Out – Open Limit Switch
Aux Relay Out – Close Limit Switch
Aux Relay Out – Gate/door Motion
Aux Relay Out – Pre-Motion Delay
Aux Relay Out – Power
Aux Relay Out – Tamper
Cycle Quantity Feedback
Fire Dept Open Input

OPERATION

COMMERCIAL/GENERAL ACCESS
Normally set to OFF. Normal gate/door
close (timer or control).
Normally set to BATT. For local jurisdiction
requirement, set to OPEN so that the
gate/door will open approximately 15
seconds after AC power fail.
Normally set to OPEN. If powered from
battery and battery is low, gate/door
automatically opens and stays open.
Normally set to OFF. CLOSE
EYES/Interrupt loop reverses a closing
gate/door.
Normally set to OFF. Normal open
speed.
Use with SAMS (Sequence Access
Management System).
Typically not required.
Attach alert signal (audible or visual alert
system).
Attach alert signal (audible or visual alert
system).
Attach visual alert to know when system
is charging batteries (i.e. not running on
batteries).
Attach alert signal (audible or visual alert
system) to indicate if gate/door is
manually tampered with by being pushed
off of close limit.
Use during servicing only to determine
operator cycles.
Connect emergency access system
(Knox box switch, SOS system, etc.).
COMMERCIAL
Normally set to OFF. Normal gate/door
close (timer or control).
Normally set to BATT. Run on battery if AC
power fails.
Normally set to CLOSE. If powered from
battery and battery is low, gate/door stays
closed.
Set to ON. In attempt to prevent vehicle
tail-gating, CLOSE EYES/ Interrupt loop
pauses a closing gate/door.
Set to ON for high speed open to
help flow in high traffic areas.
1. Use with SAMS (Sequence Access
Management System).
2. Connect "Gate Open" indicator (e.g.
light).
Connect "Gate Close/Secure" indicator
(e.g. light).
Attach alert signal (audible or visual alert
system).
Attach alert signal (audible or visual alert
system).
Attach visual alert to know when system
is charging batteries (i.e. not running on
batteries).
Attach alert signal (audible or visual alert
system) to indicate if gate/door is
manually tampered with by being pushed
off of close limit.
Use during servicing only to determine
operator cycles.
Typically not required.
23
INDUSTRIAL
Set to ON, so that gate/door closes
immediately after vehicle passes CLOSE
EYES/Interrupt loop.
Normally set to BATT. Run on battery if AC
power fails.
Normally set to CLOSE. If powered from
battery and battery is low, gate/door stays
closed.
Set to ON. In attempt to prevent vehicle
tail-gating, CLOSE EYES/ Interrupt loop
pauses a closing gate/door.
Set to ON for high speed open to
help flow in high traffic areas.
1. Use with SAMS (Sequence Access
Management System).
2. Connect "Gate Open" indicator (e.g.
light).
Connect "Gate Close/Secure" indicator
(e.g. light).
Attach alert signal (audible or visual alert
system).
Attach alert signal (audible or visual alert
system).
Attach visual alert to know when system
is charging batteries (i.e. not running on
batteries).
Attach alert signal (audible or visual alert
system) to indicate if gate/door is
manually tampered with by being pushed
off of close limit.
Use during servicing only to determine
operator cycles.
Typically not required.