Specific Safety Instructions; Technical Data - REMS Amigo 2 Instructions D'emploi

eng
e) Maintain power tools. Check for misalignment or binding of moving parts,
breakage of parts and any other condition that may affect the power tools
operation. If damaged, have the power tool repaired by a qualified expert
or by an authorised REMS after-sales service facility before use. Many
accidents are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with
sharp cutting edges are less likely to bind and are easier to control.
g) Secure the workpiece. Use clamps or a vice to hold the workpiece. This is safer
than holding it with your hand, and also it frees both hands to operate the equip-
ment.
h) Use the power tool, accessories and tool bits etc., in accordance with these
instructions and in the manner intended for the particular type of power
tool, taking into account the working conditions and the work to be performed.
Use of the power tool for operations different from those intended could result in
a hazardous situation. All unauthorised modifications to the power tool are
prohibited for safety reasons.
E) Battery tool use and care
a) Ensure the switch is in the off position before inserting battery pack. Inserting
the battery pack into power tools that have the switch on invites accidents.
b) Recharge only with the charger specified by the manufacturer. A charger
that is suitable for one type of battery may create a risk of fire when used with
another battery pack.
c) Use battery tools only with specifically designated battery packs. Use of
any other battery packs may create a risk of injury and fire.
d) When battery pack is not in use, keep it away from other metal objects like
paper clips, coins, keys, nails, screws, or other small metal objects that
can make a connection from one terminal to another. Shorting the battery
terminals may cause bums or a fire.
e) Under abusive conditions, liquid may be ejected from the battery, avoid
contact. If contact accidentally occurs, flush with water. If liquid contacts
eyes, additionally seek medical help. Liquid ejected from the battery may
cause irritation or bums.
f) Do not use the battery/charger at battery/charger temperatures or ambient
temperatures of ≤ 5°C/40°F or ≥ 40°C/105°F.

1. Technical Data

1.1. Article numbers
Drive unit
Guiding support
REMS Dual purpose holder
Die heads for
pipe threads
tapered, right-hand
ISO 7-1
(DIN 2999, BSPT)
1.2. Capacity
Thread diameters
Pipes
Bolt (both)
Types of threads
External threads
right- and left-hand
Pipe threads parallel
(with button die)
Threads for electric conduit
Pipe threads parallel
(with button die)
Bolt threads
(with button die)
Thread lengths
Pipe threads tapered
Pipe threads parallel,
conduit, bolt
Nipples and double-nipples with
the REMS Nippelspanner
(internal clamping)
1.3. Revolutions of die head
Automatically, infinitely
variable rotation (rpm)
1.4. Electrical data
230 V, 50/60 Hz
Power input
Rated current input
Fuse protection
Intermittent service
REMS
Mini-Amigo
530001
533100
R ⅛" 521000
R ¼" 521010
R ⅜" 521020
R ½" 521030
R ¾" 521040
R 1"
R 1¼"
R 1½"
R 2"
⅛"– ¾"
––
––
––
––
⅜"– ¾"
30 –18
500 W
2.3 A
10 A (B)
2/10 min
g) Do not dispose defective batteries in the normal domestic waste. Take them
to an authorised REMS after-sales service facility or to a reputed waste
disposal company.
F) Service
a) Have your power tool serviced by a qualified repair person using only
identical replacement parts. This will ensure that the safety of the power tool
is maintained.
b) Comply with maintenance instructions and instructions on tool replace-
ments.
c) Check mains lead of power tool regularly and have it replaced by a qualified
expert or an authorised REMS after-sales service facility in case of damage.
Check extension cable regularly and replace it when damaged.

Specific Safety Instructions

● Use only original REMS eva quick-change die heads! It cannot be assured that
other die heads fit securely or they may damage the octagonal seat of the drive
unit.
● Always use the support bracket! Otherwise there is a danger of the unit being
torn from the hand as the torque increases and spinning round.
● Do not work without retaining ring (11). Otherwise the die head may be pushed
out, e.g. during start-cutting.
● Combustible propellant (butane) is added to REMS thread-cutting oils in spray
cans (REMS Spezial, REMS Sanitol) which is environment-friendly. Spray cans
are pressurized – do not force open. Also, protect them from exposure to strong
sunlight and heating above 50°C.
● Due to the degreasing effect of the thread-cutting oils, an intensive skin contact
must be avoided. An appropriate skin protector must be applied.
● Do not allow undiluted thread-cutting oil to get into drainage, water systems or
the soil. Remaining thread-cutting oils have to be delivered to specialized waste
disposal companies. Disposal identity number for mineral-based thread-cutting
oils 54401, for synthetic 54109.
REMS REMS
Amigo E Amigo
530003 530000
533000 533000
543100 543100
521000 521000
521010 521010
521020 521020
521030 521030
521040 521040
521050 521050
521060
521070
521080
⅛"–1" ⅛"–1¼"
6 – 30 mm, ¼"–1"
R (ISO 7-1, DIN 2999, BSPT) NPT
G (DIN ISO 228, DIN 259,
BSPP) NPSM
M×1.5 (DIN EN 60423, IEC)
Pg
M, BSW, UNC
standard length
50 mm (with reclamping unlimited)
⅜"–1" ⅜"–1¼"
35 – 27 35 – 27
950 W 1200 W
6 A 6 A
10 A (B) 10 A (B)
2/10 min 2/10 min
REMS REMS Amigo 2
Amigo 2 Compact
540000 540001
543000 543010
543100 543100
521000 521000
521010 521010
521020 521020
521030 521030
521040 521040
521050 521050
521060 521060
521070
521080
⅛"– 2" ⅛"– 2"
⅜"– 2" ⅜"– 2"
30 –18 30 –18
1700 W 1200 W
8.3 A 6 A
16 A (B) 10 A (B)
2/10 min 2/10 min
eng