Publicité
Les langues disponibles
Les langues disponibles
2. Application
2.1 How to prepare the application
All product-related illustrations can be found on
the cover flap of this booklet.
Check the device to ensure the packaging is free
from external damage and complete. Make sure
before use that the device and accessories are
visibly undamaged and that all packaging material
has been removed.
· Lay out all parts ready (Fig.
)
1
· Hold the pump head as shown in Fig.
2
· Charge the pump head for at least 2 hours before
using it for the first time as described in Point
When the charging cable is connected, the motor
cannot be started.
· As soon as the pump head is fully charged, you
can assemble all the parts.
· Press the pump head onto the larger opening of
the cylinder, as shown in Fig.
5
· First, attach the large ring loader on the other
side of the cylinder and then the smaller constric-
tion ring onto it (Fig.
)
6
· Insert the cone into the small ring loader (Fig.
· Apply some lubricant to the tip of the cone
(Fig.
)
8
· First, place the largest constriction ring (20 mm)
on the top of the cone. Slide the constriction ring
over the cone onto the small ring loader. Now
take off the cone (Fig.
)
9
· The erection aid is now is ready for use.
2.2 How to use the erection aid
The erection aid is for your personal use only. It
may not be passed on to third parties, nor be used
by them. Never use this erection aid if you have
drunk alcohol or have taken recreational drugs. Do
not continue using the erection aid if it does not
work properly.
8
Important: Never wear the constriction ring on the
penis for more than 30 minutes. Do not fall asleep
with the constriction ring on the penis! Use the
device only in your domestic environment, and not
under the shower or in the bathtub.
· Remove the pubic hair directly on the penis and
around the root of the penis.
· The device must fit the skin tightly.
· Apply some lubricant to the edge of the ring
loader. (Fig.
)
10
· Introduce the penis through the ring loader into
the cylinder. (Fig.
)
11
· Press the device tightly to your body.
· Keep the button
on the pump head permanent-
4
ly pressed down. (Fig.
)
12
· The motor in the pump head starts and begins to
suck air out of the cylinder.
· As long as you keep the button
pressed down,
the device sucks air out of the cylinder.
· As soon as you release the button
switches off. (Fig.
)
12
Do you see a good erection in the cylinder?
· Then push the constriction ring from the ring
)
loader onto the stiff penis.
7
· Slide the constriction ring quickly and as far as
possible down to the base of the penis. (Fig.
· Now release the erection aid from the body.
To do this, keep the button
pressed (Fig.
This allows air to enter the cylinder, and you can
easily detach the erection aid from the body.
· The constriction ring on the penis causes the
penis to remain rigid. (Fig.
)
15
· Now you can have sex.
After sex:
· Briefly pull the constriction ring apart on the
flaps.
· Wait until the blood has flown back from the
penis into the body.
· Then pull the constriction ring off the penis.
When you use the erection aid, you will have no
visible ejaculation upon orgasm (climax). (Fig.
· The constriction ring retains the semen (ejacu-
late) in the penis.
· As soon as you remove the constriction ring, the
seminal fluid flows out of the penis.
· The temporary retention of the semen in the
penis is not harmful.
· After using the erection aid, clean it as described
in section "How to clean the erection aid"
· Dry the parts.
· Put all parts back into the bag and keep the erec-
tion aid out of the reach of children.
Application notes:
Application of this erection aid is easy. Neverthe-
less, it is better to try the erection aid initially alone
and unhurried. Then you can show the erection aid
to your partner. Once you both know how to use
the erection aid correctly, you can enjoy sex again.
Even at an advanced age, in illness or physical lim-
itation.
, the motor
2.3 How to select the proper constriction ring
To keep your erection as long as possible, you
need to choose the proper constriction ring. If the
constriction ring is too large, your penis will not
remain stiff for long. If the constriction ring is too
tight, it may cause pain. In case of pain, take off the
)
constriction ring and try a larger constriction ring.
13
When you use the erection aid for the first time, it
).
is best to start with the largest constriction ring. If
14
the constriction ring is too large, try a smaller one
until you find the right size for yourself. The erec-
tion aid includes 2 ring loaders. The smaller one is
slightly narrower, the larger one a bit wider. If the
smaller ring loader is too narrow, just use the larger
one. The two ring loaders are suitable for all con-
striction rings. Thus, it does not matter which con-
striction ring size you are using. If both ring loaders
are too narrow, you can slip the constriction ring
directly onto the cylinder. The erection aid also
includes the cone. It helps you to slip the constric-
tion ring more easily onto the ring loaders. Alter-
natively, you can slip the constriction ring manually
)
onto the ring loaders without using the cone. Use
16
only the supplied constriction rings. From time to
time, the constriction rings need to be replaced.
You can make repeat purchases from your dealer.
3. Cleaning and storing the device
Before cleaning, take the pump head off the erec-
tion aid. The pump head may only be cleaned with a
damp cloth from the outside. The pump head must
never be held under water as liquid can otherwise
enter and damage the pump head. Do not use any
detergents or solvents. All other parts can be easily
cleaned with warm water and mild soap. Store the
erection aid in the pouch provided in order to avoid
contamination.
4. Charging the battery
Do not charge the device during use.
How can I tell when the battery is empty?
The Active
Erection System is equipped with a
3®
lithium ion battery. When the battery is almost
empty, the button
repeatedly glows red. The
device now needs to be charged (Fig.
a)
4
· Place the charging cable on the charging contact
on the pump head.
· Charge the pump head for at least 2 hours.
· During the charging process, the button
with a red pulsating light. (Fig.
)
4
· When the button
glows white, the device is
charged and ready for operation. (Fig.
b)
4
5. Side effects / contraindications
If you have a blood coagulation or blood formation
disorder (e.g. sickle cell anaemia, blood cancer,
bone marrow tumours, anticoagulant therapy),
contact your doctor before you first use the
product.
You can get a bruise (haematoma) at the base or at
the top of the penis. Sometimes, there may even
be slight tissue injury, when the penis was not erect
for a long time. If you have diseases that cause a
prolonged erection or in which sexual intercourse
should be avoided, do not use the erection aid.
glows
9
Publicité
Chapitres
