Kreg FOREMAN DB210-EUR Mode D'emploi page 3

soap and water. Allowing dust to get into your mouth, eyes, or
lay on the skin may promote absorption of harmful chemicals.
WARNING: A dust mask or respirator should be worn by all
persons entering the work area. The filter should be replaced daily or
7) The label on your machine and this manual may include the symbols
whenever the wearer has difficulty breathing. See your local hardware below. The symbols and their definitions are as follows:
store for the proper NIOSH/OSHA approved dust mask.
V volts
are as follows:
• The label on your tool may include the following symbols. The
Hz hertz
symbols and their definitions are as follows:
A .......amperes
A .......amperes
V ......... volts
A amperes
W ......watts
W ......watts
Hz ....... hertz
watts
W
.....alternating current
min ..... minutes
.....alternating current
alternating current
.....alternating or direct current
... direct current
n o ......no load speed
.....alternating or direct current
no load speed
....... Class I Construction
n o ......no load speed
......earthing terminal
min
revolutions per minute
-1
........... (grounded)
.....safety alert symbol
Class II Construction (double insulated)
....... Class II Construction
......earthing terminal
BPM ..beats per minute
........... (double insulated)
Meets European Union safety, health, and
.....safety alert symbol
environmental protection requirements
RPM ..revolutions per minute
.../min per minute
BPM ..beats per minute
General warning
Read, understand, and follow all
RPM ..revolutions per minute
instructions before attempting to use this
product.
Turn tool off and disconnect tool from
power source before making any
adjustments or removing or installing
attachments or accessories.
Wear approved eye and hearing protection.
Keep hands away from the rotating drill
bit and workpiece clamp area when
operating the machine.
Do not expose to rain or use in a damp
location.
Do not wear jewelry or loose clothing
while operating.
Do not dispose with household waste.
Dispose separately from municipal waste
stream.
WARNING
Dust created by sanding, sawing, grinding, drilling, and
other construction activities may contain chemicals known to cause
cancer and birth defects or other reproductive harm. Examples of these
chemicals are:
a) Lead from lead-based paints
b) Crystalline silica from bricks and cement and other masonry products
c) Arsenic and chromium from chemically treated lumber
Your risk from exposure to these chemicals depends on how often you do
this type of work. To reduce your exposure, work in a well-ventilated area with
approved safety equipment, such as a dust mask specifically designed to filter
out microscopic particles.
General Safety Instructions
Foreman DB210-EUR specifications
Input ................................................ 220V-240V~50-60Hz 600W
No-load speed .................................. 2,800 min-1
Minimum workpiece thickness ......... 13mm
Maximum workpiece thickness ........ 45mm
Standard drill bit ................................ 9.5mm-diameter, 157mm overall length,
Total mass including accessories .... 11 kg
A .......amperes
Hand-Arm Vibration Level of the Foreman DB210-EUR Pocket-Hole Machine
Vibration total values determined according to EN 61029
W ......watts
No Load Acceleration at handle
Vibration emission value ah= 0.472 m/s
.....alternating current
Uncertainty K= 1.5 m/s
.....alternating or direct current
Load Acceleration at handle
Vibration emission value ah= 4.34 m/s
n o ......no load speed
Uncertainty K= 1.5 m/s
......earthing terminal
ATTENTION
differ from the declared total value depending on the way in which the tool is used.
.....safety alert symbol
Noise emission value
BPM ..beats per minute
Noise emission declaration according to EN ISO 4871
A-weighted sound pressure level measuring
RPM ..revolutions per minute
Unloading: Position 1-5
Loading: Position 1-5
Uncertainty KpA = 3 dB.
A-weighted sound power level measuring
Unloading: Calculated
Loading: Calculated
Uncertainty KwA = 3 dB.
WARNING
numbness, tingling and reduced ability to grip. Long term exposure can lead to
a chronic condition. If necessary, limit the length of time exposed to vibration
and use anti-vibration gloves. Do not operate the tool with hands below a
normal comfortable temperature, as vibration will have a greater effect. Use the
figures provided in the specification relating to vibration to calculate the duration
and frequency of operating the tool.
Sound and vibration levels in the specification are determined according to
EN 61029 or similar international standards. The figures represent normal
use for the tool in normal working conditions. A poorly maintained, incorrectly
assembled, or misused tool, may produce increased levels of noise and
vibration. www.osha. europa.eu provides information on sound and vibration
levels in the workplace that may be useful to domestic users who use tools for
long periods of time.
Guidelines for extension cord use
Extension cords are only to be used for temporary purposes. They do not
replace the need for installation of outlets and proper wiring where necessary.
To reduce the risk of electric shock when using a power tool outdoors, use an
extension cord rated for outdoor use.
In the shop and on construction sites:
1. Extension cords with an equipment grounding conductor must be used
2. Extension cords must be protected from damage, and not run through
3. Extension cords should be rated for the requirements of the electrical
4. Extension cords must be periodically inspected to ensure that the insulation
5. Extension cords should not be run through water or allowed to have
2
2
The vibration emission during actual use of the power tool can
User exposure to tool vibration can result in loss of sense of touch,
at all times.
doorways or windows where the doors or windows may close, causing
damage to the cord.
equipment in use with a conductor cross-section area not less than .75mm
and conductivity of the wires are not compromised.
connections that may be exposed to accumulated water.
stepped tip
2
2
LpA =90.3 dB(A)
LpA =91 dB(A)
LwA = 101dB(A)
LwA = 101.8 dB(A)
2.
.
2