Description Of Device / Spare Parts; Assembly; Before The First Start-Up; Chain Lubrication (Oil-Automatic) - ATIKA KSC 40-35 Notice Originale

Description of device / spare parts 
Pos. Order-No. Denomination
1 364685 Guide bar (sword)
2 364686 Saw chain 91P0-52X
3 Fastening screw
3a Handle of fastening screw
4 Chain tension ring
5 364825 Cover
6 364827 Chain tensioner
7 Seal Oil flow canal
8 364829 Chain wheel
9 On/Off switch
10 Rear handle
11 Eco-mode switch
12 Trip switch
13 Front handle
14 Front hand guard (chain brake)
15 Claw stopper
16 364826 Oil tank cap
17 362921 Guide bar cover (scabbard)
18 364822 Safety label
19 400144 Saw chain oil 1 l (without picture)
20 365500
Charger 1,8 Ah
21 365501
Li-Ion battery 2,0 Ah
22 365503
Li-Ion battery 4,0 Ah

Assembly

 Observe the enclosed mounting sheet!
Connect the chain saw to the power supply system
only after having finished the complete assembly
Risk of injury!
Wear protective gloves when assembling.
Installing the guide bar and the saw chain
Put the chain saw downward on an even face.
Loosen the mounting screw (3) by folding the handle (3a)
upward and turning it clockwise. Remove the cover (5).
Insert the saw chain (2) into the circular guide slot of the
guide bar (1).
Attend to the correct running direction of the
chain links.
Put on the guide bar (1). The guide bar retainer (A) must
reach into the slot of the guide rail.
When assembling, pay attention that the chain
links are lying correctly within the guide slot
and on the chain wheel (18).
Saw chain can hardly be put around the chain wheel?
Turn the chain clamp (20) anti-clockwise until the saw
chain can easily be put around the chain wheel. Turn the
chain clamp (c) clockwise until the saw chain is firmly
clamped.
Remount the cover (5).
Clamping the saw chain as described in section
Clamping of saw chain
„
20
.
"

Before the first start-up

Chain lubrication
The chain saw is not delivered filled with saw chain
adhering oil
Any use without chain saw oil may result in

damage of the saw chain and guide bar.
Avoid eye and skin contact. Wear protective
gloves!
The durability and cutting power of the chain depends on the
optimal lubrication. During operation the saw chain is
automatically wetted with oil.
Charging the oil tank
Put the chain saw on a suitable base
Unscrew the oil tank lock (16).

Fill the oil tank with bio-degradable chainsaw oil
(order no. 400144).
The fill level can be seen on the inspection window. For
easier filling use a funnel
When filling observe that no dirt reaches the oil
tank
Screw on the oil tank lock (16) again

Never use recycled oil or used oil. The guarantee
expires when using oil which is not allowed for such
devices.
Battery
The lithium ion batteries AP 40-4000 (Article No.
365503) or AP 40-2000 (Article No. 365501) as well

as the charger ALG 40-1800 (Article No. 365500) are
not included in the scope of delivery and must be
purchased separately.
Use only an original battery and the original
charger.

Refer to the respective "Operating instructions" for further
information on the batteries and the charger.

Inserting the battery

Activate the chain brake.
Use the back of your hand to press
against the front hand guard (14).
Insert the battery (22/23) in the device.

Make sure to slide the battery fully in until it engages
with a click.

Start-up

Switching on / off

Make sure before each startup that the switch lock, the
On/Off switch and the chain and motor brake are working
properly