Safety Instructions For Installation And Maintenance Work; Unauthorised Modification And Manufacture Of Spare Parts; Improper Use; Transport And Temporary Storage - Wilo SiBoost Smart Série Notice De Montage Et De Mise En Service

English
• If hot or cold components on the product/unit lead
to hazards, measures must be taken by the cus-
tomer to prevent them from being touched.
• Guards for moving components (such as the cou-
pling) must not be removed whilst the product is
in operation.
• Leakages (e.g. from the shaft seals) of hazardous
fluids (which are explosive, toxic or hot) must be
led away so that no danger to persons or to the
environment arises. National statutory provisions
are to be complied with.
• Highly flammable materials should always be kept
a safe distance from the product.
• Danger from electrical current must be eliminated.
Local directives or general directives [e.g. IEC, VDE
etc.] and instructions from local energy supply
companies must be adhered to.
2.6 Safety instructions for installation and
maintenance work
The operator must ensure that all installation and
maintenance work is carried out by authorised and
qualified personnel who have sufficiently familiar-
ised themselves with the installation and operat-
ing instructions by studying them in detail.
Work on the product/unit must only be carried out
when at a standstill. The procedure described in
the installation and operating instructions for
shutting down the product/unit must be strictly
observed.
Immediately upon completing work, all safety and
protective devices must be put back in position
and/or recommissioned.
2.7 Unauthorised modification and manufacture of
spare parts
Unauthorised modification and manufacture of
spare parts will impair the safety of the product/
personnel and void the manufacturer's declara-
tions regarding safety.
Modifications to the product are only permissible
following consultation with the manufacturer.
Genuine spare parts and accessories authorised by
the manufacturer ensure safety. If other parts are
used, the manufacturer is no longer liable for any
consequences which arise from this.

2.8 Improper use

The operational reliability of the supplied product
is only guaranteed for intended use in accordance
with section 4 of the installation and operating
instructions. The limit values must on no account
fall below or exceed those values specified in the
catalogue/data sheet.
8

3 Transport and temporary storage

The pressure-boosting system is supplied on a
pallet (see examples Fig. 12), on transport boards
or in a crate and is film-wrapped to protect it
against moisture and dust. Transport and storage
instructions applied to the packaging must be
observed.
CAUTION! Risk of property damage!
Use approved lifting gear (Fig. 12) to transport
the system. Ensure the stability of the load
since, with this particular pump design, the cen-
tre of gravity is shifted to the top (top-heavy).
Connect transport slings or ropes to the trans-
port eyes provided (see Fig. 1a, 1b, 1c, 12 -
item 13) or around the base frame. The pipes are
not suitable to withstand loads and should not
be used to secure loads in transit.
CAUTION! Risk of damage!
Loading of the pipes in transit can result in leaks!
NOTICE!
Where systems are fitted with casings it is recom-
mended that these are removed using the lifting
gear before transport, and are refitted after all
installation and set-up work has been completed
(see Fig. 11a and 11b).
The transport dimensions, weights and necessary
passageways and transport areas of the system
can be taken from the supplied installation plan or
other documentation.
CAUTION! Risk of detriment or damage!
The system must be protected by means of suit-
able measures against moisture, frost and heat
and also mechanical damage!
When receiving and unpacking the pressure-
boosting system and the supplied accessories,
first check the packaging for damage.
If damage is found which may have been caused
by the system having fallen or similar impacts:
• Check the pressure-boosting system and acces-
sories for possible damage.
• Inform the delivery company (forwarding agent)
or our customer service, even if you do not
find any obvious damage to the system or its
accessories.
After removing the packaging, store or install the
system according to the described installation
conditions (see section titled Installation).
WILO SE 08/2018