Novoferm iso20-4 Notice De Montage page 12

GB
Move the door leaf to its end position and guard against it
falling down. Firstly, remove the safety plug from the cable
link. Then remove the single cables from the lower cable
link on the left and right sides.
( 44 ) Close the door slowly and carefully.
( 45 ) Beginning with the top section, dismantle each section in
the reverse sequence to installation.
( 46 ) Continue dismantling the door in reverse order as de-
scribed in the installation instructions.
Operating and maintenance instructions for
iso20-4 / iso45-4 sectional garage doors with
tension springs
Incorrect operation or maintenance renders the manufac-
turer's liability null and void, as does failure to use original
spare parts or any unauthorized changes to the structure
of the door.
Operation:
The mechanical equipment of this door is designed to mitigate
to the greatest possible extent the risk of anyone operating or
standing near the door being crushed, cut, clipped or otherwise
injured. To ensure safe use of the door, the following points
must be observed:
 Make sure nobody and nothing is within range of moving
parts (e.g. door leaf, rollers, etc.) before and while operat-
ing the door.
 Manual operation of the sectional garage door is only per-
missible using the outer handles, inner handles, or the
manual cable. The operator must always keep his hands
away from moving parts.
 Lock function
 Turning the key fully enables the sectional garage door
to be opened and closed without a key at all times.
 Turn the key 3/4 to open the door and back the other
way 3/4 to lock it when closed.
 The inside unlocking/locking knob can be activated to
enable opening and closing without a key.
 Keep people and objects out of opening range when oper-
ating the sectional garage door from inside or out.
When opening the door leaf, make sure it is in end position

and has come to a standstill before taking any other action.
Sufficient spring tension must be available. To adjust the
spring tension, see sections 34ff.
Caution: The spring tension may only be adjusted by a
qualified installer!
Operation of this door is only permissible at temperatures
between -30°C and +40°C.
 Make sure the catch engages securely when closing the
sectional garage door.
 When equipping this door with an operator,
 the system must comply with all applicable EU Direc-
tives (Machinery, Low Voltage, EMC Directives, etc.),
as well as with all applicable national and international
norms and regulations
 the system must be duly fitted with a type plate and CE
mark by the manufacture, and a declaration of perfor-
mance must have been issued
 handover literature must be available in the local lan-
guage and must be kept in a safe place throughout the
service life of the garage door
 the staple plates, catches and bolt bars must be dis-
mantled.
Keep these installation, operating, and maintenance instructions in a safe place during the entire service life of the garage door.
Removal of the manual cable is absolutely essential!
Adjustments to the garage door operator may only be
performed by appropriately qualified installers!
Maintenance:
The following must be checked following installation of the
garage door and every 6 months thereafter, at least.
Maintenance by unskilled or appropriately qualified install-
ers:
 Check the garage door in accordance with the test instruc-
tions (sections 31ff.).
Grease the roller axes in the holders and clean the pairs of

horizontal tracks once installation of the sectional garage
door is complete and at intervals of approx. 5,000 cycles.
 Do not grease the lock cylinder; if it does not run smoothly
enough, treat it with graphite spray.
 Ensure sufficient ventilation (drying) of the door frame;
water drainage must also be ensured.
 Keep all corrosives or other aggressive agents such as
acids, lyes, salts, fertilizers, etc. away from the sectional
garage door.
 Steel-filled sectional garage doors are coated with polyes-
ter at the factory. Any paintwork on site must be applied
within 3 months from delivery using 2C epoxy primer con-
taining solvents and, once hardened, standard paint.
 Touch up the paint at intervals as required by local envi-
ronmental and atmospheric conditions.
 We recommend wiping the door regularly with a soft, damp
cloth. If necessary, use a mild cleaning agent or soap with
lukewarm water. Avoid using any polishing agents or abra-
sive or organic solvents/cleaning agents. Before cleaning,
flush the door and glazing thoroughly with water to avoid
scratches caused by dust particles.
Maintenance by suitably qualified installers:
 Check screws and clamp connections for secure fit and
tighten if necessary.
 Check wearing parts (springs, double cables, etc.) and
replace with original spare parts, if necessary.
 Check that the spring tension is correct. To adjust the
spring tension, see sections 34ff of the installation instruc-
tions.
 Replace the multiple spring assemblies and double cables
after approx. 25,000 cycles (open/close).
This is necessary:
Every 14 years for 0 - 5 cycles a day
Every 7 years for 6 - 10
Every 3.5 years for 11 - 20
- 9 -
"
"