Safety Requirements; Technical Data And Accessories; Safety Regulations - Stiga SBC 627 K Manuel D'utilisation

Masquer les pouces Voir aussi pour SBC 627 K:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 162
20. Harness
a. with single belt
b. with double belt
c. with backpack
21.  Angle transmission
22. Blade protection (for transport)
23.  Spark plug
31.  Engine stop switch
32. Throttle control
33.  Throttle lockout
34. Starter grip
35.  Choke 
36.  Primer
37. Throttle shutter (if provided)
38.  Fuel mixture tank cap
The  example  of  the  conformity  declaration  is 
found in the penultimate page of the manual.
DESCRIPTION OF EXPLANATORY
SYMBOLS (where applicable)
41.  Fuel mixture tank
42.  Engine stop switch positions
a = stop
b = running
43.  Choke
44.    C utting device with adequate protection
45. Cutting device rotation direction

SAFETY REQUIREMENTS

Your  machine  must  be  used  carefully.  Symbols 
have therefore been placed on various parts of
the  machine  to  remind  you  of  the  main  precau-
tions  to  be  taken.  Their  meaning  is  explained 
below.  You  are  also  asked  to  carefully  read  the 
safety regulations in the specific chapter of this 
manual. 
Replace damaged or illegible labels.
51.    W arning! Danger. The failure to use this ma-
chine correctly can be hazardous for oneself 
and others.
52.    R ead  the  instruction  manual  before  using 
the machine.
53.    A nyone  operating  the  machine  under  nor-
mal conditions for continuous daily use may 
be  exposed  to  a  noise  level  equal  to  or  ex-
ceeding 85 dB (A). Wear ear protectors,
safety goggles and a protective helmet.
54.    W ear gloves and protective footwear!
55.    P rojectile  object  hazard!  Keep  any  people 
or  pets  at  least  15  m  away  when  using  the 
machine!
56.    M aximum  cutting  device  speed.  Only  use 
suitable cutting devices.
57.    D o  not  use  circular  saw  blades.  Danger:
Using circular saw blades with ma-
chines marked with this symbol expos-
es the user to the danger of very serious
or even fatal injuries.
58.    W arning!  Petrol  is  flammable.  Allow  engine 
to cool at least 2 minutes before refuelling.
59.  Beware of blade thrust.
60.    W arning! - The engine emits carbon monox-
ide. DO NOT start up in an enclosed area.

TECHNICAL DATA AND ACCESSORIES

[71] Mass
[72] Engine
[73]  2-stroke air-cooled
[74]  Capacity / Power
[75]  Engine rotation speed when idling
[77]  Maximum tool rotation speed
[78]  Fuel tank capacity
[79]  Spark plug
[80]  Fuel mixture (Petrol: 2-stroke oil)
[81]    M aximum diameter allowed for blades with 
3 or 4 points
[82]  Maximum diameter allowed saw blade
[83] Operator ear noise pressure level
[84]  Measurement uncertainty
[85]  Measured acoustic power level
[86]    V ibrations transmitted to the hand
on the front handgrip
[87]    V ibrations transmitted to the hand
on the rear handgrip
[88]    V ibrations transmitted to the hand
on the left handgrip
[89]    V ibrations transmitted to the hand
on the right handgrip
[90]  Guaranteed acoustic power level
[91] Cutting device code
[92] Protection code
[93]  Availability:
          X = standard machine feature
          O = optional, available on request
(–) not provided

SAFETY REGULATIONS

to be observed scrupulously
A) TRAINING
1)  Read  the  instructions  carefully.  Become  ac-
quainted  with  the  controls  and  the  proper  use 
of  the  machine.  Learn  how  to  stop  the  engine 
quickly.
11

Publicité

Table des Matières
loading

Table des Matières