Ryobi RHT400 Manuel D'utilisation page 13

GB
F D E I
GENERAL SAFETY RULES
the risk of starting the power tool accidentally.
Store idle power tools out of the reach of children and
n
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
Maintain power tools. Check for misalignment or
n
binding of moving parts, breakage of parts and any
other condition that may affect the power toolʼs
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
Keep cutting tools sharp and clean. Properly
n
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
Use the power tool, accessories and tool bits etc.
n
in accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations
different from those intended could result in a
hazardous situation.
SERVICE
Have your power tool serviced by a qualified repair
n
person using only identical replacement parts.
This will ensure that the safety of the power tool is
maintained.
HEDGE TRIMMER SAFETY WARNINGS
Keep all parts of the body away from the cutter blade.
n
Do not remove cut material or hold material to be
cut when blades are moving. Make sure the switch
is off when clearing jammed material. A moment of
inattention while operating the hedge trimmer may
result in serious personal injury.
Carry the hedge trimmer by the handle with the
n
cutter blade stopped. When transporting or storing
the hedge trimmer always fit the cutting device cover.
Proper handling of the hedge trimmer will reduce
possible personal injury from the cutter blades.
Keep cable away from cutting area. During operation
n
the cable may be hidden in shrubs and can be
accidentally cut by the blade.
ADDITION
Advice to check the hedge for foreign objects, e.g.
n
wire fences.
Recommendation for the use of a residual current
n
All manuals and user guides at all-guides.com
P NL S DK N FIN GR HU CZ RU RO PL SLO HR TR EST LT
English
device with a tripping current of 30mA or less.
Instruction to hold the hedge trimmer properly, e.g.
n
with both hands if two handles are provided.
SPECIFIC SAFETY RULES
Never operate the product without the safety guard in
n
place and in good condition.
Keep the working area free from wires, nails, metallic
n
cable, glass, stones and debris.
Do not cut against hard objects, this could cause
n
injury or damage the trimmer.
Do not cross roads or gravel paths with the trimmer
n
still running.
As equipment user, you are responsible for third
n
parties in the working area.
While operating the tool, always hold it firmly with
n
both hands by the two handles and ensure a firm
footing, especially if steps or ladders are used. Do not
touch the blades!
Make sure you hold the tool firmly with both handles
n
and that you are well balanced with your weight
evenly distributed on both feet.
Keep the cutting system below level of your waist.
n
Keep your fingers and other body parts away from the
n
cutting blade.
CAUTION
Certain parts of the machine may become hot
in use.
Familiarise yourself with your surroundings and be
n
on the alert for possible hazards which you may not
notice because on the noise from the machine.
Never grasp the tool by the blade.
n
Large variation in temperature can lead to condensation
n
inside the tool. Before use, give the machine time to
adjust to the temperature of work area.
Let the tool work at its own pace. Do not overload.
n
Never attempt to use an incomplete machine or one
n
fitted with an unauthorised modification.
When transporting, disconnect the plug from the
n
mains. Carry the trimmer by the handles provided
and keep hands away from the blade.
During transport or storage, always cover the blade
n
with the blade sheath (6).
WARNING
NEVER USE THE TOOL WITHOUT THE
SAFETY GUARD.
LET THE TOOL WORK AT ITS OWN PACE.
DO NOT OVERLOAD.
10
LV SK BG