Kärcher B 110 R Mode D'emploi page 22

5. Install the batteries if the device was de-
livered without batteries (see chapter
"Before inital startup/ batteries").
6. Drive the device forward and off the pal-
let (see chapter "Operation / Driving").
Installing he brushes
1. The installation of the brushes is de-
scribed in the chapter "Maintenance
work".
Installing the suction bar
1. Pivot both clamping levers upwards.
Suction hose
1
Suction bar suspension
2
Suction bar
3
Clamping lever
4
2. Insert the suction bar in the suction bar
mount.
3. Pivot both clamping levers downwards.
Batteries
Recommended battery sets
Descrip- Order no. Volume
3
tion (m
170 Ah - 4.039- 2.4
Mainte- 352.7
nance-
free, AGM
180 Ah - 4.039- 3.8
Mainte- 354.7
nance-
free, gel
285Ah - 4.039- 12.6
Mainte- 353.7
nance-
free, AGM
* Minimum volume of the battery charging
room
** Minimum airflow between battery charg-
ing room and environment
Installing and connecting batteries
CAUTION
Removing and installing the batteries
Unstable machine position
22
Ensure that the machine is positioned sta-
bly when removing and installing the batter-
ies.
ATTENTION
Incorrect connection polarity
Destruction of the control electronics
Take care to ensure the correct polarity
when connecting the batteries.
ATTENTION
Deep discharge
Risk of damage
Charge the batteries before starting the de-
vice.
1. Drain the waste water.
2. Unlock the waste water tank and pivot it
up.
3. Place the battery in the device.
170 Ah, 4.039-352.7
Spacer 310x85x70 mm
1
Spacer 240x55x30 mm
2
180 Ah, 4.039-354.7
Spacer 310x85x70 mm
1
Airflow
3
)* (m /h)**
1.0
1.6
5.1
285 Ah, 4.039-353.7
Spacer 345x60x47
1
4. Insert the spacers at the locations
shown in the picture between the battery
and the device.
5. Connect the battery terminals using the
connection cables provided.
6. Clamp the connecting cables on the (+)
and (-) battery terminals that are still
free.
Note
For the 170 Ah 4.039-352.7 battery set, at-
tach the connection cable to the negative
pole with the insulated pole screw.
English
7. Connect the device-side battery connec-
tor to the battery-side battery connector.
8. Pivot the waste water tank forwards and
close it.
Removing the battery
CAUTION
Removing and installing the batteries
Unstable machine position
Ensure that the machine is positioned sta-
bly when removing and installing the batter-
ies.
1. Set the safety switch to "0".
2. Drain the waste water.
3. Unlock the waste water tank and pivot it
up.
4. Pull out the battery plug.
5. Disconnect the cable from the minus ter-
minal at the battery.
6. Disconnect the remaining cables from
the battery.
7. Remove the battery.
8. Dispose of the used batteries in accord-
ance with statutory provisions.
Initial startup
Charging the battery
DANGER
Inappropriate use of the charger
Electric shock
Adhere to the mains voltage and fuse val-
ues specified on the device type plate.
Only use the charger in dry rooms with suf-
ficient ventilation.
Flammable gases are generated when
the battery is charged
Risk of explosion
Only charge the battery in a suitable room.
The room must have a minimum volume
depending on the battery type and an ade-
quate air exchange rate with a minimum air
flow (see "Recommended batteries").
ATTENTION
Accumulation of dangerous gases un-
der the tank during the charging pro-
cess
Risk of explosion
Pivot the waste water tank upwards before
charging low-maintenance batteries.
The average charging time is approx. 10-
15 hours.
The device cannot be used during the
charging process.
Note
The device has deep discharge protection,
i.e. the brush motor and turbine are
switched off automatically when the permit-
ted minimum capacity level is reached.
1. Drive the device directly to the charger
and do not drive on slopes.
External charger
ATTENTION
Using an unsuitable charger
Risk of damage
Do not connect the charger to the device-
side battery connector.
Use only a charger suitable for the type of
battery installed.