Activation Procedure Of The "Ftc" Function; Deactivation Procedure Of The "Frt" Or "Ftc" Function; Repositioning Of Limit Switch "1; Clearing Limit Switch Positions "0" And "1 - Nice Free-Max Instructions Et Avertissements Pour L'installation Et L'utilisation

Activation procedure of the "FTC" function

8.2
01. Press and hold down key ■ (for approx. 5 sec-
(5")
onds), until the motor performs 1 VIBRATION;
1
then release the key.
02. Press and hold down keys ■ and ▼ simultane-
(5")
ously (for approx. 5 seconds), until the motor
1
1 starts to automatically move the awning into
S
position "1", then release the keys.
03. (within the next 4 seconds) Use keys ▼ and ▲
to position the awning in the release position
1
S "S", a few centimetres below the mechanical
S
release point.
04. Press and hold down keys ▼ and ▲ simultane-
0
ously, until the motor starts to automatically
move the awning from position "0" (= position
"S" memorised, FTC function activated); then
release the key.

Deactivation procedure of the "FRT" or "FTC" function

8.3
Caution! – This procedure cancels the "FRT" or the "FTC" function if pro-
grammed.
01. Press and hold down key ■ (for approx. 5 sec-
(5")
onds), until the motor performs 1 VIBRATION;
1
then release the key.
02. Press and hold down keys ■ and ▼ simultane-
(5")
ously (for approx. 5 seconds), until the motor
starts to automatically move the awning to
1
position "1"; then release the keys.
03. (within the next 4 seconds) Press and hold down
keys ■ and ▼simultaneously until the motor
2
performs 2 LONG motions (= position "2" and
FRT function deleted, or position "S" and "FTC"
function deleted), then release the keys.
REPOSITIONING OF LIMIT
9
SWITCH "1"
✔
For AWNINGS: For ROLLER SHUTTERS:
Caution! – the modification of position "1" automatically deactivates the
"FRT" or "FTC" function if programmed.
01. Press and hold down key ■ (for approx. 5 sec-
(5")
onds), until the motor performs 1 VIBRATION,
1
then release the key.
02. Press and hold down keys ■ and ▼ simultane-
(5")
ously (for approx. 5 seconds), until the motor
1
starts to automatically move the roller shutter /
1
awning into position "1", then release the keys.
03. (within the next 4 seconds) Press keys ▼ and ▲
to position the roller shutter/awning in the new
1
position "1".
1
04. (within the next 4 seconds) Press and hold
down keys ■ and ▼ simultaneously until the
2
motor performs 2 LONG motions (= new posi-
tion "1" memorised), then release the keys.
CLEARING LIMIT SWITCH
10
POSITIONS "0" and "1"
✔
For AWNINGS: For ROLLER SHUTTERS:
Caution! – Clearing of these positions automatically deactivates the
"RDC", "FRT" or "FTC" function, if programmed.
01. Press and hold down key ■ (for approx. 5 sec-
(5")
onds), until the motor performs 1 VIBRATION;
1
then release the key.
02. Press and hold down key ■ again (for approx. 5
(5")
seconds), until the motor performs 4 SHORT
4
motions; then release the key.
✔
✔
English – 15