Technical Data; Before Starting The Equipment; Attachment And Operation - Scheppach HC60 Traduction Des Instructions D'origine

• Do not process media such as white spirit, butyl
alcohol and methylene chloride with the PVC pres-
sure hose. These media will destroy the pressure
hose.
• The work area must be separated from the com-
pressor so that it cannot come into direct contact
with the working medium.
Operating pressure vessels
• You must keep your pressure vessel in good work-
ing order, operate the vessel correctly, monitor the
vessel, carry out necessary maintenance and re-
pair work immediately and meet the relevant safety
precautions.
• The supervisory authority may enforce essential
control measures in individual cases.
• A pressure vessel is not allowed to be used if it has
faults or deficiencies that can endanger workers or
third parties.
• Check the pressure vessel for signs of rust and
damage each time before using. Do not use the
compressor with a damaged or rusty pressure ves-
sel. If you discover any damage, then please con-
tact the customer service workshop.
Do not lose these safety instructions

6. Technical data

Mains connection
Motor rating
Operating mode
Compressor speed
Pressure vessel capacity
Operating pressure
Theoretical intake capacity
Theoretical delivery rate
Protection type
Weight of the unit
The noise emission values were measured in accord-
ance with EN ISO 3744.
Wear hearing protection.
The effects of noise can cause a loss of hearing.
m Warning: Noise can have serious effects on your
health. If the machine noise exceeds 85 dB (A),
please wear suitable hearing protection.
Sound power level L
wA
Sound pressure level L
pA
Uncertainty K
wA/pA
20 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

7. Before starting the equipment

• Before you connect the equipment to the mains
• Prior to initial commissioning, remove the trans-
• Check the equipment for damage which may have
• Install the compressor near the point of consump-
• Avoid long air lines and supply lines (extension ca-
• Make sure that the intake air is dry and dustfree.
• Do not install the compressor in a damp or wet
• The compressor may only be used in suitable
• The compressor is designed to be used in dry
• The compressor may only be used outdoor briefly
• The compressor must always be kept dry and must
230 V 50 Hz
1500 W

8. Attachment and operation

S1
2900 min
-1
n Important!
50 l
You must fully assemble the appliance before
10 bar
using it for the first time!
225 l/min
8.1 Fitting the wheels (9)
133 l/min
• Fit the supplied wheels (9) as shown in Fig. 4.
IP20
26 kg
8.2 Fitting the supporting foot (7)
• Fit the supplied supporting foot (7) as shown in Fig-
8.3 Installation of the air filter (13)
• Remove the transport plug and attach the air filter
• Solve for maintenance the air filter (13) by turning
8.4 Changing the transportation cover (fig. 6 - 7)
• Remove the transport lid (12) of the oil filling open-
97 dB(A)
• Fill the included compressor oil into the crank hous-
75 dB(A)
1,91 dB(A)
supply make sure that the data on the rating plate
are identical to the mains data.
port plug (12) and fill the crank housing with oil as
described in 8.4.
occurred in transit. Report any damage immedi-
ately to the transport company which was used to
deliver the compressor.
tion.
bles).
room.
rooms (with good ventilation and an ambient tem-
perature from +5 °C to 40 °C). There must be no
dust, acids, vapors, explosive gases or inflamma-
ble gases in the room.
rooms. It is prohibited to use the compressor in ar-
eas where work is conducted with sprayed water.
when the ambient conditions are dry.
not be left outdoors after work is complete.
ure 5.
(Figure 8/13) on the unit by turning clockwise.
counter-clockwise..
ing .
ing and insert the included oil sealing plug into the
oil filling opening.