Publicité
Les langues disponibles
Les langues disponibles
Use only as authorized
The machine corresponds to the valid EC guideline.
scheppach tku 4000 circular sawbench is defined
as a semi-stationary machine in accordance with pr EN
1870-1.
front and at the rear using both hands and lift the ma-
chine.
original scheppach base is not used, the machine
must be placed firmly upon a stable stand resembling a
table. The working height should be 850 mm.
the left of the sawblade.
chine must be clear of interfering foreign matter to pre-
vent accidents occurring.
i.e. nails or screws.
connected to a dust extractor with a flexible, non-flam-
mable suction hose. The suction should switch on auto-
matically when the machine is switched on.
connected to a vacuum exhaust unit.
Use the scheppach dust extractor ha 3200 or ha 2600
to remove matchwood or saw dust. The vacuum support
flow rate must be 20 m/s. Subatmospheric pressure
1200 Pa.
scheppach automatic switching unit is available as a
special accessory.
Type ALV 2
Art. No. 7910 4010 230 V/50 Hz
V/230 V/50 Hz
ter a 2-3 second delay after the machine tool is turned
on. This avoids overtoading the circuit fuse. After tuming
off the machine tool, the vacuum exhaust unit remains
on for an additional 3-4 seconds and is then automati-
cally switched off. Remaining dust is thereby removed
by vacuum exhaust, as required by German regulations
governing hazardous materials. This results in savings
in electricity consumption and reduces noise levels, as
the vacuum exhaust unit is on only during machine tool
operation.
tractor woova 7 must be used.
dust removers while machine tools are operating.
scheppach circular sawbench is designed exclu-
sively for the machining of wood and materials similar
to wood. Only original scheppach tools and accessories
may be used. Use the required sawblade in accordance
with the EN 847-1 norm depending on the type of cut
and type of wood (solid wood, plywood or chipboard).
Please observe the scheppach Special Tool Accesso-
ries.
condition in accordance with its designated use and the
instructions set out in the operating manual, and only
-
CE tested machines meet all valid EC machine guidelines as
well as all relevent guidelines for each machine.
-
scheppach dust ex-
by safety-conscious persons who are fully aware of the
risks involved in operating the machine. Any functional
disorders, especially those affecting the safety of the
machine, should therefore be rectified immediately.
erally recognized safety-technical rules must also be ad-
hered to.
scheppach machine may only be used, maintained,
and operated by persons familiar with it and instructed
in its operation and procedures. Arbitrary alterations to
the machine release the manufacturer from all responsi-
bility for any resulting damages.
scheppach machine may only be used with original
accessories and original tools made by the manufactur-
er.
is not responsible for any damages resulting from unau-
thorized use; risk is the sole responsibility of the opera-
tor.
Use only as authorized
the-art standards and the recognized safety rules. Nev-
ertheless, its use may constitute a risk to life and limb
of the user or of third parties, or cause damage to the
machine and to other material property.
scheppach circular saw bench is constructed exclu-
sively for the sawing of wood. The required saw blade
should be inserted according to the cut type and the
wood type (solid wood, chip board or plywood).
condition in accordance with its designated use and the
instructions set out in the operating manual, and only
by safety-conscious persons who are fully aware of the
risks involved in operating the machine. Any functional
disorders, especially those affecting the safety of the
machine, should terefore be rectified immediately.
be connected to a vacuum exhaust unit. Use the
scheppach vacuum exhaust unit ha 3200 or ha 2600
to remove matchwood or saw dust. The vacuum support
flow rate must be 20 m/s. Subatmospheric pressure
1200 Pa.
scheppach automatic switching unit is available
as a special accessory. The vacuum exhaust unit auto-
matically switches on after a 2-3 second delay after the
machine tool is turned on. This avoids overloading the
circuit fuse. After turning off the machine tool, the vac-
uum exhaust unit remains on for an additional 3-4 sec-
onds and is then automatically switched off. Remaining
dust is thereby removed by vacuum exhaust, as required
by German regulations governing hazardous materials.
This results in savings in electricity consumption and
reduces noise levels, as the vacuum exhaust unit is on
only during machine tool operation.
mover woova 7 must be used. Do not remove or shut
-
scheppach dust re-
11
Publicité
