Publicité
Les langues disponibles
Les langues disponibles
off vacuum exhaust systems or dust removers while ma-
chine tools are operating.
is not responsible for any damages resulting from un-
authorized use; risk is the sole responsibility of the op-
erator.
manufacturer as well as the technical data given in the
calibrations and dimensions must be adhered to.
erally recognized safety-technical rules must also be ad-
hered to.
scheppach Table Circular Saw may only be used,
maintained, and operated by persons familiar with and
instructed in its operation and procedures. Arbitrary al-
terations to the machine release the manu facturer from
all responsibility for any resulting damages.
scheppach Table Circular Saw may only be used with
original accessories and saw blades from the manufac-
turer.
Remaining hazards
The machine has been built using modem technology in
accordance with recognized safety rules. Some remaining
hazards, however, may still exist.
hands if the work piece is incorrectly fed.
is not properly secured or fed, such as working without a
limit stop.
is exceeded when working. Be sure to wear personal
protective gear such as ear protection.
spect the structural integrity of saw blades.
to injuries caused by electricity.
cessories must be observed and carefully read when
scheppach special accessories are used.
maining hazards which are not yet evident may still be
present.
instructions in „Safety Precautions", „Proper Use" and
in the entire operating manual.
Assembly
For reasons of packaging technology, your Scheppach ma-
chine is not completely pre-installed.
Put the saw tabletop on the reverse for the installation.
Insert a piece of cardboard to protect the table surface.
Assembly tools
Included in the supply volume
1 sawblade key size 10/13/17
For reasons of packaging technology, your Scheppach ma-
chine is not completely pre-installed.
12
Put the saw tabletop on the reverse for the installation.
Place a piece of cardboard underneath to protect the table
surface.
Installation of the dust suction connector, Fig. 1
1. Mount the dust suction connector on the casing cover.
4 hexagon head cap screws M6 x 10
4 hexagon nuts M6
-
Installation of the base feet, Fig. 2
1. Hand-tighten all screws and nuts.
2. Each base foot is screwed on the tabletop with 4 hexa-
gon head cap screws M6x16, 4 serrated lock washers
A6,4, and 4 hexagon nuts M6.
The cheese head screw M6 x 40 is fastened with two
nuts on the left side of the frame foot and serves as
support for the sliding stick. The running gear is fas-
tened on the rear side of the frame feet using two hexa-
gon head cap screws M8 x 16 with nuts and washers.
Then put the foot caps on the base feet.
Installation of the longitudinal and cross struts, Fig. 2
1. Each longitudinal and cross strut is screwed on the tab-
letop with 1 hexagon head cap screw M6x16, 1 serrated
lock washer A6,4, and 1 hexagon nut M6.
2. Finally tighten all screws and nuts.
Installation of the switch, Fig. 3
1. Fasten the switch mounting part with 2 hexagon head
cap screws M8x16, 2 washers A8,4, and 2 hexagon
nuts M8 on the tabletop.
Installation of the table extension, Fig. 4
1. Hand-tighten all screws and nuts.
-
2. Fasten the table extension panel with 2 hexagon head
cap screws M6x16, 2 washers ø6 and 2 hexagon nuts
M6 on the saw table rear.
3. Fasten the supporting frames with 2 hexagon head cap
-
screws M6x16, 2 hexagon nuts M6, and 2 washers ø6
on the cross strut.
4. Fasten the supporting frames with 2 hexagon head cap
-
screws M6x16 and 2 hexagon nuts M6 on the table ex-
tension.
Put the circular saw bench on its feet again. Align the ma-
chine. Adjust the table extension panel to the height of the
saw tabletop, and tighten all screws.
Transport handles and tool holder, Fig. 4.1
Install the transport handles left and right onto the feet of
the frame.
Thereto install the hex bolt (A) with a washer 6 mm, the
transport handle and a washer 6 mm onto the foot of the
frame and secure with a hex nut M6 self-locking, so that
the transport handle is still movable.
Install the cylinder bolt (B) M6x16 with a washer 6 mm left
and right onto the feet of the frame and secure from the
inside with a hex nut M6 self-locking. This will act as a stop
during transport of the saw.
Install the cylinder bolt (C) M6x35 with 2 washers and
two hex nuts onto the feet of the frame and secure. This is
Publicité
