Machine Lay Up, Dismantling And Disposal - grandimpianti WFM 33 Instructions Pour L'installation Et Mode D'emploi

www.groupdynamics-laundry.com
sales@groupdynamics.lv
Bolts Dimensions Quantity
A M20 x 65
24 (12)
B M12 x 30 8
37 kg type:
Km 13 1
C M12 x 35 6
D M30 x 80 1
E M12 x 38 4
- Check the wear and tear of the belts and, if
need be, replace them; for correct operation,
always replace the entire set of belts.
- Make sure that the safety devices are
working properly (e.g. the door microswitch
and the tilt microswitch).
- Check that the screws for electrical
connection are tight on the contactors and
power inlet terminal strip.
- Disassemble the drain valve and clean it
inside from lint.
- Check that the heaters are in perfect
condition and clean them from scale.
- Suspension adjustment: If the tub is
unlevelled or when the suspensions have
been replaced, it is necessary to adjust them
(see figure below) by tightening or loosening
the nuts (2) the same number of turns until
the distance (X) between the mobile part (4)
and the fixed part (5) is 55mm.
BEFORE TURNING THE MACHINE
BACK ON BY THE WALL CUTOFF
SWITCH, PUT ALL THE PANELS
REMOVED BACK IN PLACE.
AUTOMATIC MAINTENANCE
REQUEST
The machine keeps count of the number of
cycles it executes. After 1000 programs the
Tightening
machine will flash a writing from cycle
torque (Nm)
1001 onwards.
600,00
More precisely, when starting a new cycle,
70,00 the machine will flash the writing
"Maintenance required" for some seconds
450,00
as the START button is pressed, then it will
70,00
carry out the selected cycle normally.
800,00
When this message is displayed, request
25,00 yearly maintenance.
To call off this reading and start the 1000
cycle count from scratch, press the "DOWN"
push-button.
8.5 IDENTIFYING AND ORDERING
SPARE PARTS
To identify the codes of spare parts refer to
the exploded drawings and relevant list.
Once you have identified your codes, send a
standard written order to the manufacturer,
mentioning clearly machine model, serial
number, feed voltage and frequency and, of
course, including the code and description
of the spare part needed.
9. MACHINE LAY UP,
DISMANTLING AND DISPOSAL
If the washing machine is no longer to be
used, it is advisable to put it out of service
and suitably dispose of the resulting
materials, considering the information
provided in chapter 3. For the sake of the
environment, sort the materials in
accordance with the waste disposal
provisions in force in your country, so that
they can be properly disposed of or recycled.
All the parts composing the machine can be
treated as solid urban waste, except for the
metal parts, which yet are not classed among
special waste in most European countries.
INFORMATION TO USERS
Pursuant to article 13 of law decree 25 July
2005, nr. 151 relating to "Implementation
of Directives 2002/95/EC, 2002/96/EC and
2003/108/EC concerning the reduction in
the use of hazardous substances in electric
and electronic apparatus, as well as waste
disposal"
The deleted dustbin symbol on the appliance
indicates the product must be disposed of
separate from other wastes once it reaches
the end of its life cycle.
Once the appliance has reached the end of
its life cycle, the user must therefore take it
to a suitable pre-sorted waste centre for
electronic and electro-technical appliances,
or return it to the dealer on purchasing a new
similar appliance, on a one for one basis.
Adequate pre-sorted waste collection before
subsequently sending the appliance for
recycling, treatment and environmentally
compatible disposal helps avoid possible
negative effects on the environment and
health and favours the recycling of the
materials making up the appliance.
Unlawful disposal of the product by the user
is punishable by the administrative sanctions
indicated in law decree nr. 22/1997 (article
50 and following articles of law decree nr.
22/1997)
24