grandimpianti WFM 33 Instructions Pour L'installation Et Mode D'emploi page 19

www.groupdynamics-laundry.com
sales@groupdynamics.lv
displayed, which is made of 10 characters
and can be used to assign a program name,
e.g. "WHITES 90°C". To enter characters,
press the "SELECT" key: all the available
characters will be viewed, which can be
selected using the "UP" and "DOWN" keys.
Confirmation is automatic.
STEPS
Go to the "STEPS" field using the "UP" and
"DOWN" keys.
Confirm the selection by "ENTER".
The first step associated to the currently
selected cycle will then appear, i.e. step N°
01, which is displayed in big print.
The number assigned to the step, along with
the relevant type and comment will be
displayed in small print too.
The steps composing the currently selected
cycle and the sequence of actions associated
thereto can be scrolled using the "UP" and
"DOWN" keys: for example, soak, prewash,
wash and intermediate short spin, rinse and
so on until the last scheduled step is viewed.
A program can hold up to maximum of 25
steps. Free steps will be marked "NOT
PROGRAMMED".
Select the step to be altered using the "UP"
and "DOWN" keys and confirm by
"ENTER". The display will list the following
entries:
CHANGE
ERASE
INSERT BEFORE
INSERT AFTER
To move the cursor inside a word that is
being entered use the "UP" and "DOWN"
keys.
To delete a letter, point it with the cursor
and press "START".
When the desired text has been keyed in,
confirm by "ENTER" and exit by pressing
the "MODE" key.
Change: press "ENTER" to confirm if you
wish to change the step currently selected.
Select the step with which you wish to
replace the currently selected step using the
"UP" and "DOWN" keys. Then confirm by
"ENTER".
The programmer will next prompt
"COPY?". Press "ENTER" to confirm the
change or either press "MODE" to cancel it.
Erase: press "ENTER" to erase the step
currently selected.
The programmer will next prompt
"ERASE?". Press "ENTER" to erase or
either press "MODE" to cancel the action.
CAUTION! The "ERASE" command does
not erase steps from the programmer but
only from the sequence associated to the
selected program. The steps erased can be
selected again, re-entered or changed as
desired.
Insert before and after: press "ENTER" to
confirm that you wish to insert a step before
or after the currently selected step. Select
the step to be inserted before or after using
the "UP" and "DOWN" keys and then press
"ENTER" to confirm.
To cancel the insertion, press "MODE".
TYPE
Go to the "TYPES" field using the "UP" and
"DOWN" keys.
Confirm the selection by "ENTER".
The display will list the following entries:
STRONG
MEDIUM
DELICATE
Select cycle type using the "UP" and
"DOWN" keys and press "ENTER" to
confirm. Program type selection is a just a
reminder for the user. It is meant to assist
him in the selection of the most appropriate
cycle.
When the desired type has been selected,
confirm pushing "ENTER" and exit by the
"MODE" key.
CAUTION! This selection does not alter
cycle execution in the least. It is only a
reminder for the user.
COPY FROM AND COPY TO
Move to the "COPY FROM" or "COPY
TO" field using the "UP" and "DOWN"
keys. Press "ENTER" to confirm.
Select the program you wish to copy from or
to using the "UP" and "DOWN" keys. Press
"ENTER" to confirm.
The programmer will next prompt
"COPY?". Press "ENTER" to copy between
cycles or programs or press "MODE" to
cancel.
Whether you chose to confirm or cancel the
copy, press "MODE" to exit.
DESCRIPTION OF
PROGRAMMABLE FUNCTIONS
Machine parameters are those required to
effect marginal changes to the wash
programs without having to access cycle or
step programming.
These functions enable the user to override
existing actions or add new ones in a wash
cycle. This does not alter the program
features in a radical manner, though.
The "MACHINE PARAMETERS" menu is
accessed as follows:
Open the washer door: all programming
actions must be performed with the door
open. The programming environment
cannot be accessed when the door is closed.
Hold down the " MODE" key until the
"MACHINE PAR." reading appears. Press
"ENTER" to confirm. The display will then
read the following items:
COOL
SPIN
PREWASH
DELAYED START
BUZZER
HEATING
ENABLE
RESET
The various items are described below.
These functions affect only the currently
selected wash cycle and remain effective
until they are disabled.
20
COOLING
Cool: This function decides whether the
wash bath is to be cooled right before it is
drained off. As a rule, cooling is aimed to
prevent the garments from undergoing a
thermal shock as they go, for example, from
a 90°C wash step to ambient temperature
rinsing.
Select "COOL" using the "UP" and
"DOWN" keys.
Confirm the selection by "ENTER".
Programs/cycles and their respective cooling
setting can be scrolled using the "UP" and
"DOWN" keys. Move to the desired cycle and
press "ENTER". Then choose between "YES"
and "NO" using the "UP" and "DOWN" keys
and press "ENTER" to confirm.
Press "MODE" to exit.
SHORT SPINNING
Spin: This function allows to acknowledge
the standard-selected spinning, reduce it to
one-minute spinning or eliminate it
altogether. Select "SPIN" using the "UP"
and "DOWN" keys.
Confirm the selection by "ENTER".
Programs/cycles and their respective cooling
setting can be scrolled using the "UP" and
"DOWN" keys. Move to the desired cycle
and press "ENTER". Then again using the
"UP" and "DOWN" keys choose among:
NORMAL
REDUCED
NO SPINNING
Press "ENTER" to confirm.
Normal: the machine carries out standard
final spinning. Reduced: one-minute final
spinning. Spinning length is applied to the
last spinning speed. The acceleration ramp
is never reduced.
No spinning: final spinning is not carried
out.
Press "MODE" to exit.
NO PREWASHING
Prewash: Generally speaking, all programs
include prewash. The purpose of this
function is actually to override prewash.
This is especially useful when handling
laundry that is not heavily soiled.
Select "PREWASH" using the "UP" and
"DOWN" keys.
Confirm the selection by "ENTER".
Programs/cycles and their respective
prewash setting can be scrolled using the
"UP" and "DOWN" keys.
desired cycle and press "ENTER". Then
choose between "YES" and "NO" using the
"UP" and "DOWN" keys and press
"ENTER" to confirm.
Press "MODE" to exit.
DEFERRED CYCLE START
Delayed START: This function defers
machine start up to a maximum of 24 hours.
As soon as the scheduled time has elapsed
the machine starts automatically.
This function defers machine start up to a
maximum of 24 hours. As soon as the
scheduled time has elapsed the machine
starts automatically.
Move to the