Specific Safety Rules - Ryobi RBC430SES Manuel D'utilisation

EN
FR DE ES
fuel leaks, etc. Replace any damaged parts before
use.
The cutting attachment should never rotate at idle
Q
during normal use. The cutting attachment may rotate
at idle during carburettor adjustments.
Store fuel in a container approved for petrol.
Q
Wipe up any fuel spillage. Move 10m away from
Q
refuelling site before starting the engine. Slowly
remove the fuel cap after stopping engine. DO NOT
SMOKE when refuelling.
Stop the engine and allow it to cool before refuelling
Q
or storing the unit.
Allow the engine to cool; empty the fuel tank and
Q
secure the unit from moving before transporting in a
vehicle.
Wear protective equipment and observe all safety
Q
instructions. For units equipped with a clutch, be sure
the cutting attachment stops turning when the engine
idles. When the unit is turned off make sure the
cutting attachment has stopped before the unit is set
down.
This product is intended for infrequent use by
Q
homeowners and other occasional users for such
general applications as trimming light and heavy
vegetation, etc. It is not intended for prolonged use.
Prolonged periods of operation can cause circulatory
problems in the user's hands due to vibration. For
such use, it may be appropriate to use a device
having an anti-vibration feature.

SPECIFIC SAFETY RULES

After engine stops, keep rotating blade in heavy
Q
grass or pulpy weeds until it stops.
Do not operate the brush cutter unless the blade
Q
guard is firmly secured in place and in good
condition.
Use heavy gloves while installing or removing blades.
Q
Always stop the engine and remove the spark plug
Q
wire before attempting to remove any obstruction
caught or jammed in the blade or before removing
and installing the blade.
Do not attempt to touch or stop the blade when it is
Q
rotating.
A coasting blade can cause injury while it continues
Q
to spin after the engine is stopped or throttle trigger
released. Maintain proper control until the blade has
completely stopped rotating.
Replace any blade that has been damaged. Always
Q
make sure blade is installed correctly and securely
fastened before each use.
Use only the manufacturer's replacement TRI-ARC
Q
blade intended for use on this brush cutter. Do not
use any other blade.
IT PT NL SV DA NO FI HU CS RU
English
The TRI-ARC blade is suited for cutting pulpy weeds
Q
and vines only. Do not use for any other purpose.
Never use the TRI-ARC blade to cut woody brushes.
Exercise extreme caution when using the blade with
Q
this unit. Blade thrust is the reaction that may occur
when the spinning blade contacts anything it cannot
cut. This contact may cause the blade to stop for
an instant, and suddenly "thrust" the unit away from
the object that was hit. This reaction can be violent
enough to cause the operator to lose control of the
unit. Kick back can occur without warning if the blade
snags, stalls, or binds. This is more likely to occur in
areas where it is difficult to see the material being
cut. For cutting ease and safety, approach the weeds
being cut from the right to the left. In the event an
unexpected object or woody stock is encountered,
this could minimize the blade kick back reaction.
Never cut any material over 13mm diameter.
Q
Always wear the shoulder strap when using the brush
Q
cutter and adjust to a comfortable operating position.
Maintain a firm grip on both handles while cutting with
a blade. Keep the blade away from body and below
waist. Never use the brush cutter with the blade
located 75cm or more above the ground level.
Cover the blade with the blade protector before
Q
storing the unit, or during transportation. Always
remove the blade protector before using the unit. If
not removed, the blade protector could become a
thrown object as the blade begins to turn. thrown
object as the blade begins to turn.
Inspect before use. Replace damaged parts. Make
Q
sure fasteners are in place and secure. Check for fuel
leaks.
Replace cutting blade if cracked, chipped, or
Q
damaged in any way. Be sure the blade is properly
installed and securely fastened. Failure to do so can
cause serious injury.
Make sure all guards, straps, deflectors, and handles
Q
are properly and securely attached.
Use only the manufacturer's replacement cutting
Q
blade. Do not use any other cutting attachment. To
install any other brand or cutting head to this brush
cutter can result in serious personal injury. Never
use, for example, wire or wire-rope, which can break
off and become a dangerous projectile.
Never operate the unit without the guard in place and
Q
in good condition.
Always shut the engine off before fuelling. Never add
Q
fuel to a machine with a running or hot engine. Move
at least 10m from the refuelling site before starting
engine. Wipe up any fuel spillage. DO NOT SMOKE.
Failure to heed this warning could result in serious
personal injury.
17
RO PL SL HR ET LT LV SK BG