Specific Safety Rules - Ryobi RHT2660DA Manuel D'utilisation

GB
F D E
machine, a guard or other part that is damaged should be
carefully checked to determine that it will operate properly
and perform its intended function. Check for alignment
of moving parts, binding of moving parts, breakage of
parts, mounting and any other conditions that may affect
its operation. A guard or other part that is damaged must
be properly repaired or replaced by an authorized service
center to avoid risk of personal injury.
NEVER LEAVE MACHINE RUNNING UNATTENDED.
■
TURN POWER OFF. Don't leave machine until it comes
to a complete stop.
KEEP THE ENGINE FREE OF GRASS, LEAVES, OR
■
GREASE to reduce the chance of a fi re hazard.
KEEP THE ExHAUST PIPE FREE OF FOREIGN OB-
■
JECTS.
FOLLOW MANUFACTURER'S RECOMMENDATIONS
■
FOR SAFE LOADING, UNLOADING, TRANSPORT,
AND STORAGE OF MACHINE.
KEEP MACHINE DRY, CLEAN, AND FREE FROM
■
LUBRICANT AND GREASE. Always use a clean cloth
when cleaning. Never use brake fl uids, petrol, petroleum-
based products, or any solvents to clean machine.
STAY ALERT AND EXERCISE CONTROL. Watch what
■
you are doing and use common sense. Do not operate
tool when you are tired. Do not rush.
DO NOT OPERATE THE PRODUCT WHILE UNDER THE
■
INFLUENCE OF DRUGS, ALCOHOL, OR ANY MEDICA-
TION.
CHECK THE WORK AREA BEFORE EACH USE. Re-
■
move all objects such as rocks, broken glass, nails, wire,
or string which can be thrown or become entangled in
the machine.
DO NOT USE MACHINE IF SWITCH DOES NOT TURN
■
IT ON AND OFF. Have defective switches replaced by
an authorized service center.
BEFORE CLEANING, REPAIRING, OR INSPECTING,
■
shut off the engine and make certain all moving parts have
stopped. Disconnect the spark plug wire, and keep the
wire away from the plug to prevent accidental starting.
AVOID DANGEROUS ENVIRONMENT. Don't use in
■
damp or wet locations or expose to rain. Keep work area
well lit.
NEVER USE IN AN EXPLOSIVE ATMOSPHERE. Nor-
■
mal sparking of the motor could ignite fumes.
DO NOT OPERATE WHILE SMOKING OR NEAR AN
■
OPEN FLAME.
DO NOT OPERATE at night, at times of heavy fog, or at
■
any other times when your fi eld of vision might be limited
and it would be diffi cult to gain a clear view of area.
Be familiar with all controls and the proper use of the
■
machine.
Beware of overhead power lines.
■
The cutting mechanism strikes any foreign object or the
■
I P NL S DK N FIN GR HU CZ RU
English
machine should start making any unusual noise or vibra-
tion, shut off the power source and allow the machine to
stop. Disconnect the spark plug wire from the spark plug
and take the following steps:
1. inspect for damage;
2. check for and tighten any loose parts;
3. have any damaged parts replaced or repaired with
Stop the engine and disconnect the spark plug wire from
■
the spark plug before
1. when adjusting the working position of the cutting
2. cleaning or clearing a blockage;
3. checking, maintenance or working on the machine.
Do not inhale fuel fumes as they are toxic.
■

SPECIFIC SAFETY RULES

OPERATE THE UNIT BY BOTH HANDS.
■
DO NOT OPERATE AROUND dry brush, twigs, cloth
■
rags, or other fl ammable materials.
NEVER START THE MACHINE if ice has formed in any
■
part of the equipment.
DO NOT USE ACIDS, ALKALINES, SOLVENTS,
■
FLAMMABLE MATERIAL, OR INDUSTRIAL GRADE
SOLUTIONS in this product. These products can cause
physical injuries to the operator and irreversible damage
to the machine.
NEVER ATTEMPT TO MAKE ANY ADJUSTMENTS
■
WHILE THE ENGINE (MOTOR) IS RUNNING (except
where specifically recommended by the manufac-
turer).
PROTECTIVE COVERS MUST ALWAYS COVER RO-
■
TATING PARTS WHEN THE ENGINE IS RUNNING.
KEEP COOLING AIR INTAKE (recoil starter area) and
■
muffl er side of the engine at least 1m away from
buildings, obstructions, and other burnable objects.
KEEP THE ENGINE AWAY FROM FLAMMABLES
■
AND OTHER HAZARDOUS MATERIALS.
KEEP AWAY FROM HOT PARTS. The muffl er and
■
other engine parts become very hot, use caution.
DO NOT TOUCH THE SPARK PLUG AND IGNITION
■
CABLE when starting and operating the engine.
CHECK FUEL HOSES AND JOINTS for looseness and
■
fuel leakage before each use.
CHECK BOLTS AND NUTS for looseness before each
■
use. A loose bolt or nut may cause serious engine
problems.
12 12
RO PL SLO HR TR EST LT
parts having equivalent specifi cations.
device;
LV SK BG