RIB MASTER Wi-Fi FR Mode D'emploi page 22

G
B
E -
MASTER Wi-Fi FR POWER
After having made all of the connections, provide power to the control panel.
The yellow LED DL6 should turn on and the buzzer will emit a sound indicating correct power.
The LED DL7 will flash red/green indicating that no remote controls have been memorized.
F -
IDENTIFICATION OF SAFETY DEVICES
If control panel has 2 inputs for the different management of the safety edges TOUCH
Wi-Fi and VERTIGO Wi-Fi in opening and closing:
EDGE 1 = yellow wire - safety edge in opening (LED EDGE PHOT from 1 to 3)
EDGE 2 = green wire - safety edge in closing (LED EDGE PHOT from 4 to 6)
If control panel has 1 input for the management of the safety edges, than connect just
EDGE = yellow wire - safety edge in opening and closing (LED EDGE PHOT from 1 to 3)
Every Wi-Fi safety device must OBLIGATORILY be identified placing only one of the 6 DIPs
present on its circuit (different for each of the 6 safety devices) in the ON position. Obviously
one pair of photocells is considered one safety device and must therefore have infrared ray
receiver and transmitter with the same DIP in the ON position.
ATTACH THE YELLOW NUMBERED STICKER TO EACH SAFETY DEVICE COVER TO
IDENTIFY IT WITH THE NUMBER OF THE DIP TURNED ON ON MASTER CARD.
The sticker is used to quickly identify the safety device which needs maintenance.
Note: Each safety device is supplied with the DIPs in OFF position so that battery power is
maintanined when not in use (if inserted).
Insert the batteries in the Wi-Fi safety devices.
G -
MEMORIZATION OF THE SAFETY DEVICES
After having attached the yellow numbered stickers to the safety devices covers, and
having inserted the batteries, on MASTER place the DIPs with the same numbers in the
ON position.
Use the following procedure for memorization:
- Push the button PROG RX on the MASTER Wi-Fi FR => LED EDGE PHOT 1 flashes red
for 1 minute (the time provided for memorization).
- Push the button PROG TX on the safety device with DIP 1 in ON position => LED
EDGE PHOT 1 since red, turns green and a sound from the buzzer indicates that the
safety device has been memorized correctly. Immediately the LED EDGE PHOT 2 begins
flashing red.
- If there are no other safety devices to be memorized, after one minute LED EDGE
PHOT 2 will turn off or, push the button PROG. RX 4 times to end the memorization
procedure => all of the LED EDGE PHOT must be off.
MEMORIZATION OF OTHER SAFETY DEVICES
- After having memorized the first safety device, LED EDGE PHOT 2 automatically begins
flashing red for 1 minute (the time provided for memorization).
- Push the button PROG. TX on the safety device with DIP 2 in ON position => LED
EDGE PHOT 2 flashing red, turns green and a sound from the buzzer indicates that the
safety device has been memorized correctly.
- Follow the same procedure for any other safety devices (up to a maximum of 6).
ADDING OTHER SAFETY DEVICES (UP TO 6 TOTAL)
If after installation the use of further safety devices is desired to increase door safety, it is
recommended to:
- Turn off power to the door.
- Place the safety device in the desired position and identify it by moving the internal DIP.
- Identify it with the corresponding yellow numbered sticker (see paragraph F -
IDENTIFICATION OF Wi-Fi SAFETY DEVICES).
- Enable the DIP of the safety device just added to the MASTER Wi-Fi FR card.
- Return power to the door.
- Follow the memorization procedure and system check as indicated previously.
NOVA Wi-Fi AND VERTIGO Wi-Fi PHOTOCELLS - SYSTEM CHECK
- Check that DIP selected on the infrared ray transmitter TX NOVA Wi-Fi is the same as that
selected on the receiver RX NOVA Wi-Fi (ex: DIP 1 ON).
- Proper operation of TX NOVA Wi-Fi is shown by the green LED which turns on for 10
seconds.
- Push and release the button S3 "PROG. TX" on the NOVA Wi-Fi receiver (it turns on for
3 minutes to perform the alignment procedure). If the photocells are already aligned the
red LED emits a steady light. If the red LED is off or emits a flashing light, perform the
alignment until it emits a steady light.
- After the alignment, check it by placing an obstacle so that the red LED turns off and at
the same time the LED EDGE PHOT, paired with it, turns on green for the time that the
obstacle is present.
- On MASTER card, LED DL3 should also be off indicating a proper exchange of the contact
on PHOTO input of the control panel.
- Repeat the procedure to the other photocells.
- Perform a function check to all the photocells, activating the movement of the automation
and checking that by placing an obstacle the automation stops/reverses when closing, or
stops/continues to open when opening.
TOUCH Wi-Fi STRIP - SYSTEM CHECK
After having adjusted the TOUCH Wi-Fi strip correctly:
- Press the gummy of a TOUCH Wi-Fi strip (for example: safety strip with DIP 3 ON).
- EDGE PHOT LED 3 flashes green and LED DL2 momentarily turns off and then turns on.
ATTENTION: after receiving the first signal, other signals are ignored for 2 seconds. If
there is a signal in these 2 seconds it will be from the EDGE PHOT LED 3
which turns green.
- Repeat the LED activation check on the MASTER Wi-Fi FR pressing the other TOUCH Wi-Fi
strips installed.
- Perform a final check of all strips installed, activating the movement of the automation
and ensuring that upon impact with the strip the automation stops/reverses movement.
ANTENNA 868MHz
In order to communicate with 868 MHz Wi-Fi safety devices, MASTER Wi-Fi OS is equipped
with a piece of electric wire that acts as an antenna linked to the J8 terminal. If it is
necessary to improve the radio signal (for example, with MASTER Wi-Fi OS inserted in a
metallic box), connect the 868.3 MHz antenna (code ACG5451) to the J8 terminal, ensuring
the correct connection of the central and shield wires of the aerial cable, and position it in
such a way so that it is "in view" of all safety devices.
To get the system working properly it is necessary that between MASTER and
safety devices there are no obstacles such as reinforced cement walls, iron
surfaces, etc. that could block the radio signals.
ANTENNA 433MHz
For commands working at 433,92 MHz, connect it to terminals 1-2 on MASTER.
NOVA Wi-Fi AND VERTIGO Wi-Fi PHOTOCELL ALARM SIGNAL CHECK
Check that by taking the battery out of photocell receiver with DIP 3 ON (for example), and
commanding the door to open, the LED EDGE PHOT 3 flashes green/red, while LEDs DL1,
DL2 and DL3 turn off, and that buzzer emits tones for 1 minute.
Repeat the check for any other photocell receivers installed.
Note: if removing the battery and commanding the door to open the buzzer on MASTER
Wi-Fi FR does not sound, DIP 3 is OFF on the MASTER Wi-Fi F (safety not enabled). Turn
it ON.
TOUCH Wi-Fi STRIP ALARM SIGNAL CHECK
Check that by taking the battery out of the transmitter with DIP 3 ON (for example), LED
EDGE PHOT 3 flashes red while LED DL2 turns off, and that buzzer emits every 3 seconds
a tone for 1 minute.
Repeat the check for any other strips installed.
Note: if the battery is removed and the buzzer on the MASTER Wi-Fi does not sound, DIP 3
is OFF on MASTER Wi-Fi FR (safety not enabled). Turn it to ON.
WARNING (replace the batteries)
The WARNING informs the user to replace the batteries immediately.
22
12/24V ac/dc