Connecting Optional Equipment - Sony MHC-V800 Mode D'emploi

Set the minutes in the same way. "OFF"
appears and the hour digits flash in the
display.
CD TIMER
1 2 3 4 5
6 7 8
DOLBY NR OFF
63 125 250 500 1k 2k 4k 8k 16k(Hz)
1DISC
flashing
.
CD TIMER
1 2 3 4 5
6 7 8
DOLBY NR OFF
63 125 250 500 1k 2k 4k 8k 16k(Hz)
1DISC
flashing
8
Use the JOG dial to set the hour you
want the system to turn off and press
ENTER/NEXT.
Set the minutes in the same way.
9
Press POWER to turn off the system.
The power will go on 15 seconds before
the preset time and the volume level is
automatically set to the minimum.
To change the preset timer settings
Start over from step 1.
To check the preset times settings
1 Press TIMER.
2 Press t SELECT and use the JOG dial to
select "REC".
3 Press ENTER/NEXT.
The preset items appear in the display
sequentially, then the original display
returns.
To cancel the timer
1 Press TIMER.
2 Press t SELECT and use the JOG dial to
choose "TIMER OFF."
3 Press ENTER/NEXT.
The timer indicators disappear from the
display.
If the power is on at the preset time
The sound source will automatically
change to the tuner, but tuner recording
will not start.
Notes
•You cannot set the timer so that the timer
ON and OFF times are the same.
•You cannot activate wake-up timer and
timer-recording at the same time.
•The timer operation starts 15 seconds
before the timer ON time, if you perform
another operation during that period, the
timer operation may not be performed
correctly.
Connecting Optional
Equipment
REC
VOLUME
For greater enjoyment of your stereo
system, you can connect other components
to the stereo. You can connect:
•a VCR
REC •an MD recorder
VOLUME
•a turntable
•a super woofer
•headphones
Connecting a VCR
By connecting the audio outputs terminals
from your VCR to the AUDIO IN terminals
on the rear of the stereo system you can
enjoy your videos in powerful stereo
sound. Make sure you connect the plugs to
jacks of the same color.
By connecting the AUDIO OUT and VIDEO
(or S-VIDEO) OUT terminals to the input
terminals on your VCR, you can record the
audio and video signals from VIDEO CD
and CD-G on video tape. See the operating
instructions supplied with your video deck
for details.
rear panel
Connect
AUDIO LINE OUT
jacks of the VCR
AUDIO LINE IN
jacks of the VCR
VIDEO LINE IN
jack of the VCR
S-VIDEO LINE IN
jack of the VCR
To listen to sound from the VCR
Press FUNCTION repeatedly to select
"VIDEO".
If you cannot select "VIDEO" by pressing
FUNCTION
Select "MD" and turn the power off. Then,
press POWER while holding down
FUNCTION.
"MD" will be switched to "VIDEO".
To return to "MD", repeat this procedure.
Connecting an MD or DAT
Deck
Select one of the following two connections,
depending on the equipment to be
connected and the method of recording.
•an MD or DAT deck for digital recording
•an MD or DAT deck for analog recording
When recording VIDEO CDs, be sure to use
the connections for analog recording
To connect an MD or DAT deck for
digital recording
You can record from the CD into the MD
recorder digitally.
rear panel
VCR
Connect
DIGITAL IN
(OPTICAL) jack of
the MD or DAT
With
deck
AUDIO IN jacks
(using an audio cord)
continue to next page
(not supplied)
AUDIO OUT jacks
(using an audio cord)
(not supplied)
VIDEO OUT jack
(using a supplied
video cord)
S-VIDEO OUT jack
(using an S-VIDEO
cord) (not supplied)
MD or
DAT deck
With
CD DIGITAL OUT
OPTICAL (using an
optical cable)
(not supplied)
Chapter 7: Additional Features
EN
31